Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 61 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 61

Installing the Electrolytic Capacitors

Capacitors (Electrolytic)

4

470uf 16v

C1, C2, C3, C4

The next step is to solder in the 4x 470uf 16v capacitors.

These capacitors are electrolytic and

they are polarized

which means they have to go in a certain way

- the

capacitor has a long leg and a short leg - the short leg is
the negative side and the long leg is the positive side.

You will see a + marking on the board, align the long leg on
the side closest to the + marking on the PCB.

Installing the Film (non-polarized) Capacitors

Capacitors (Non-polarized)

2

0.1uf 630v

C5, C6

The final step is to install the 2 x 0.1uf
630v  film  capacitors.  These  can  go  in
either  way  but  it  is  recommended  that
the strip is on the side with the analog
signal  entering.  These  capacitors  will
be  installed  on  the  underside  of  the
board  as  shown  opposite  -  the  reason
for  the  heat  shrink  is  because  the
casing  on  the  caps  is  conductive  and
could  short  any  circuitry  touching  the
case.

You can then proceed to cut the extra leads. Note that these are made from
silver wire so may be very useful to keep around for future projects!

«
...
59
60
61
62
63
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: QFX Pages: 44

Brand: Barco Pages: 8

Brand: Barco Pages: 3

Brand: Barco Pages: 61

Brand: Cambridge Audio Pages: 4

Brand: Cambridge Audio Pages: 2

Brand: Tascam Pages: 35

MaitreView 4KLite

Brand: AVLink Pages: 10

Brand: Eminent Pages: 31

Brand: Linear Technology Pages: 22

Brand: Solplanet Pages: 55

iSignager iS-1620

Brand: QNAP Pages: 9

Brand: DieHard Pages: 24

Brand: tams elektronik Pages: 26

david delight pro

Brand: mind alive Pages: 28

Brand: DeLOCK Pages: 16

Brand: Giandel Pages: 8

Brand: Systech Corporation Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands