Audio Note DAC Kit 3.1 Page 36 Instruction Manual Download | Manualshive

Page: 36 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 36

Then take the twisted thick RED wires
and connect these to the 300V 300V
on the PCB.

The picture opposite is what your M2 Power supply board
should now look like!

Installing the Heatsink

Feel  free  now  to  “place”  (do  not  screw  in)  your  newly
assembled board into position in the chassis.

Now  install  the  metal  heatsink  under  where  the  regulators
will sit. This must be firmly attached to the chassis.

One  more  step  and  then  time  for  a  coffee  break  on  a  job
well done!

«
...
34
35
36
37
38
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: WALKMAN Pages: 6

Brand: Z3 Technology Pages: 27

Brand: Fagor Pages: 12

Brand: K&S BASIC Pages: 17

Brand: V-TAC Pages: 4

Brand: Palmer Pages: 2

Brand: Velleman Pages: 48

Brand: OT Systems Pages: 16

Brand: Alca Power Pages: 8

Brand: Gbxpoint Pages: 4

Brand: Envertech Pages: 2

Brand: RME Audio Pages: 68

Hubner Berlin POG 86

Brand: Baumer Pages: 36

Brand: GoMax Electronics Pages: 12

Brand: Optelecom-nkf Pages: 4

Brand: Datavideo Pages: 28

Brand: ADF Web Pages: 29

Brand: Axis Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands