Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 50 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 50

Note that each capacitor only has the POSITIVE side noted
– You will have to locate the Stripe on the capacitor as
shown above and insert correctly

– Don‟t be confused by

the two caps close together.

The picture opposite shows the capacitors correctly
installed.

Installing the Diodes

Semiconductor Devices

4

Schotkey Diodes

D1, D2, D3, D4

NOTE

: This board has been designed to accept either standard diodes or Schotkey diodes (fast recovery diodes).

Schotkey diodes are supplied with the kit but we will also show how to install standard diodes.

Schotkey diode Installation

For correct installation of the diode shown you will notice
the

– sign on the top of the DIODE case that denotes the

negative side. Also note the white DOT on the board noting
positive side.

«
...
48
49
50
51
52
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

OMX-HDMI-HDB1X8

Brand: Ocean Matrix Pages: 6

Brand: Yarvik Pages: 36

Brand: YASKAWA Pages: 4

Brand: APsystems Pages: 24

Brand: Lenze Pages: 28

Brand: Manhattan Pages: 2

Brand: Meicheng Pages: 8

EQUINOX EQX 10000-2T

Brand: Salicru Pages: 24

Brand: Audio Note Pages: 7

Brand: Magnimage Pages: 40

Brand: HEIDENHAIN Pages: 6

Brand: Amptek Pages: 8

Brand: Victron energy Pages: 34

Brand: Caen Pages: 17

Brand: I.D. AL Pages: 26

Brand: M-Audio Pages: 20

Brand: Badger Meter Pages: 12

Sunny Island 3324

Brand: SMA Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands