Audio Note DAC Kit 3.1 Instruction Manual Download | Manualshive

Page: 72 / 79

background image

Copyright © 2006-2011 AudioNote Kits

www.AudioNoteKits.com

[email protected]

Page 72

Connecting the USB Input

If using the USB input then you will want to examine the
three holes in the “XLR” footprint on the Digital Board.

You will notice that there are three holes that the XLR
would normally fit into

– this is where we are going to hook

up the USB inputs.

To prepare for USB connection you will need to put a
jumper from the circular pad in the center to the rectangular
pad on the right.

This is the GROUND connection and the signal from the
USB goes to the loan OVAL pad.

This picture shows the connection of the USB (signal

– red)

to the Digital Board input.

«
...
70
71
72
73
74
...
»

Summary of Contents for DAC Kit 3.1
















































































Reviews:

No comments

Related manuals for DAC Kit 3.1

Brand: Harmonic Pages: 27

Brand: Xantrex Pages: 78

Brand: Xanter Pages: 54

Brand: YMGI Pages: 64

Brand: April Music Pages: 11

Brand: Fronius Pages: 190

Brand: Speaka Professional Pages: 8

Brand: Contec Pages: 49

Brand: Audio Technica Pages: 11

Brand: leadsun Pages: 8

Brand: ZeeVee Pages: 8

Brand: JDS Labs Pages: 5

Brand: ZIMO Pages: 79

Brand: Marshall Electronics Pages: 2

Brand: Samlexpower Pages: 26

Brand: Avtron Pages: 16

Brand: Oracom Pages: 20

Brand: BARIX Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands