Ateis PRIMA-VA/R User Manual Download Page 63

Page: 63 / 75

7.6

How to configure network options and functionalities

PRIMA VA is a standalone system, that means it can be used without any network communication.

But it is possible to connect PRIMA VA to a network in case product should be able to send and receive
to/from third party equipment. In that case, a fault report can be activated in case connection is not active
(refer to Troubleshooting section).

It is also possible to connect PRIMA VA to an NTP server, to synchronize PRIMA VA date and time.

Click on

Advanced config

Network.

Parameter

Access

Description

Fault if link down

Read / Write

Fault report if network connection is not active

NTP Server

Read / Write

NTP server IP address

Click on Apply changes to save modifications.

Summary of Contents for PRIMA-VA/R












































































Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands

Ateis PRIMA-VA/R, User Manual

Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands