Ateis PRIMA-VA/R User Manual Download Page 53

Page: 53 / 75

6.9

How to monitor amplifiers and loudspeaker lines

Click on

Basic config

Monitoring.

Amplifier monitoring is based on voltage ratio between amplifier signal input and output, measured on
pilot tone signal.

Loudspeaker line monitoring is based on impedance measurement, measured on pilot tone signal.

Pilot tone frequency can be set to 20 or 22k Hz. 1k Hz reference is used to check if loudspeaker line
wiring is correct or not.

More than one amplifier can be configured as backup amplifier. But only one backup amplifier can used
at one time. If this backup amplifier is faulty, second backup amplifier takes over, and so on according to
number of backup amplifiers.

Parameter

Access

Description

Power mode

Read / Write

Power supply monitoring: AC only, DC only or AC and DC

Frequency

Read / Write

Monitoring frequency for impedance measurement: 20 or 22k Hz

Gain tolerance

Read / Write

Difference between amplifier gain measure and reference before
fault report

Impedance tolerance

Read / Write

Difference between loudspeaker line impedance measure and
reference before fault report

Leakage threshold

Read only

Fault report if earth leakage measure is lower than leakage
threshold

Monitoring

Read / Write

Monitoring mode: Not monitored, Amplifier only, Amplifier + Line,
Backup amplifier

Amp Gain Unloaded

Read only

Amplifier gain reference when loudspeaker line is not connected to
amplifier (internal relay open)

Amp Gain Loaded

Read only

Amplifier gain reference when loudspeaker line is connected to
amplifier (internal relay closed)

Summary of Contents for PRIMA-VA/R












































































Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands

Ateis PRIMA-VA/R, User Manual

Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands