Ateis PRIMA-VA/R User Manual Download Page 32

Page: 32 / 75

Static Gain

Read / Write

Front microphone gain adjustment

Priority

Read / Write

Front microphone priority – Lowest priority = 0 – Highest priority =
100

Monitored

Read / Write

Contact and microphone capsule monitoring – Fault report for
contact and microphone capsule

Security

Read / Write

Front microphone is allowed to page even if mains power supply
is missing

Evacuation

Read / Write

Evacuation LEDs are lighting and evacuation relay is active when
front microphone is paging

Click on Apply changes to save modifications.

Click on Back to list to jump to

Basic config > Audio page.

6.4.3.

To configure call station microphone

Click on

Call Station 1

Call station 2

(audio inputs).

Parameter

Access

Description

Sensitivity

Read / Write

Maximum input level before overload

Static Gain

Read / Write

Call station microphone gain adjustment

Priority

Read / Write

Call station priority – Lowest priority = 0 – Highest priority = 100

Monitored

Read / Write

Call station monitoring – Fault report for audio link, serial link,
microphone capsule

Security

Read / Write

Call station is allowed to page even if mains power supply is missing

Evacuation

Read / Write

Evacuation LEDs are lighting and evacuation relay is active when
call station is paging

Click on Apply changes to save modifications.

Click on Back to list to jump to

Basic config > Audio page.

Summary of Contents for PRIMA-VA/R












































































Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands

Ateis PRIMA-VA/R, User Manual

Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands