Ateis PRIMA-VA/R User Manual Download Page 30

Page: 30 / 75

6.4.1.

To configure analog audio inputs

Click on

Audio Input 1

Audio Input 2.

AGC Max Gain

and

AGC Target Level

are displayed only if

Auto Gain Control

option is selected.

Static Gain

is displayed only if

Auto Gain Control

option is not selected.

Activity Threshold

and

Activity Hold Time

are displayed only if

Activity Detection Events

option is

selected.

Monitoring Threshold

and

Monitoring Time-out

are displayed only if

Monitored

option is selected.

Parameter

Access

Description

Sensitivity

Read / Write Maximum input level before overload

Auto Gain Control

Read / Write

Automatic adjustment of input signal to maintain a constant signal
level

AGC Max Gain

Read / Write Maximal gain applied to input signal

AGC Target Level

Read / Write Target level after adjustment

Noise Gate

Read / Write Audio input mute if audio signal is lower than fixed threshold – Noise

gate threshold = - 70 dB

24V Phantom

Read / Write Phantom power for condenser microphone

Static Gain

Read / Write Audio input gain adjustment

Priority

Read / Write Audio input priority – Lowest priority = 0 – Highest priority = 100

Activity Detection

Read / Write Modulation detection on audio input

Activity Threshold

Read / Write Input signal level to unmute audio input

Summary of Contents for PRIMA-VA/R












































































Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands

Ateis PRIMA-VA/R, User Manual

Search results

Summary of Contents for PRIMA-VA/R

Reviews:

Related manuals for PRIMA-VA/R

Brands by name

Popular brands