manualshive.com logo in svg

ASV SC50 Scout, Service & Repair Manual

The ASV SC50 Scout Service & Repair Manual is a comprehensive resource for maintaining and troubleshooting your ASV SC50 Scout vehicle. This manual provides detailed instructions, diagrams, and helpful tips to ensure efficient repairs and service. Download this manual for free from manualshive.com to keep your Scout in peak condition.

Share
Download
background image

7. Chassis and Fuel Tank

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 7-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 7-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 7-1
Removal & Installation  . . . . . . . . . . . . . . . . . 7-1

Hand Throttle Assembly  . . . . . . . . . . . . . . 7-1
Cargo Bed  . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Fuel Sending Unit  . . . . . . . . . . . . . . . . . . . 7-4
Fuel Tank  . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
R.O.P.S. (rollcage) . . . . . . . . . . . . . . . . . . . 7-5
Rear Console  . . . . . . . . . . . . . . . . . . . . . . 7-6
Torsion Axles  . . . . . . . . . . . . . . . . . . . . . . . 7-7

8. Radiator and Oil Cooler

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 8-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 8-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 8-1
Removal & Installation  . . . . . . . . . . . . . . . . . 8-1

Radiator/Oil Cooler  . . . . . . . . . . . . . . . . . . 8-1
Fan, Fan Spacer & Shrouding . . . . . . . . . . 8-2

9. Hydraulic Reservoir

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 9-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 9-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 9-1
Removal & Installation  . . . . . . . . . . . . . . . . . 9-1

Hydraulic Reservoir  . . . . . . . . . . . . . . . . . . 9-1
Suction Screen  . . . . . . . . . . . . . . . . . . . . . 9-3

10. Hydraulic Components

Chapter Overview  . . . . . . . . . . . . . . . . . . . . .10-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . .10-1
Machine Preparation . . . . . . . . . . . . . . . . . . .10-1
Removal & Installation  . . . . . . . . . . . . . . . . .10-1

Charge/Auxiliary Pump  . . . . . . . . . . . . . . .10-1
Tandem (Drive) Pump  . . . . . . . . . . . . . . . .10-2
2-speed/Brake Manifold  . . . . . . . . . . . . . .10-5
Shuttle Block   . . . . . . . . . . . . . . . . . . . . . .10-6
Pilot Generation Block . . . . . . . . . . . . . . . .10-7
Auxiliary Valve/Solenoid Block Assembly  .10-8
Steering Valve & Plunger   . . . . . . . . . . . . .10-9
Directional Control Valve  . . . . . . . . . . . . . .10-10

11. Engine

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 11-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 11-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 11-1
Removal & Installation  . . . . . . . . . . . . . . . . . 11-1

Battery  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Exhaust  . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
Air Cleaner Housing  . . . . . . . . . . . . . . . . . 11-4
Engine  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5

12. Undercarriage

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 12-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 12-1
Machine Preparation . . . . . . . . . . . . . . . . . . . 12-1

Removal & Installation  . . . . . . . . . . . . . . . . . 12-1

Idler Wheels 10”  . . . . . . . . . . . . . . . . . . . . 12-1
Idler Wheels 14”  . . . . . . . . . . . . . . . . . . . . 12-3
Drive Sprocket  . . . . . . . . . . . . . . . . . . . . . . 12-3
Drive Motor  . . . . . . . . . . . . . . . . . . . . . . . . 12-5
Grease Tensioner  . . . . . . . . . . . . . . . . . . . 12-6

13. Hydraulic Component Service

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 13-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 13-1
Disassembly & Assembly  . . . . . . . . . . . . . . . 13-1

Hydraulic Cylinders  . . . . . . . . . . . . . . . . . . 13-1
Auxiliary Control Valve  . . . . . . . . . . . . . . . 13-4
Drive Motor (brake portion)  . . . . . . . . . . . . 13-5
Drive Motor (motor portion)  . . . . . . . . . . . . 13-6
Drive Pump Relief Valves  . . . . . . . . . . . . . 13-8
Posi-Power Relief Valve  . . . . . . . . . . . . . . 13-8
Drive Pump (disassembly)   . . . . . . . . . . . . 13-9
Drive Pump (assembly)  . . . . . . . . . . . . . . . 13-11
Auxiliary Pump  . . . . . . . . . . . . . . . . . . . . . 13-12

14. Hydraulic Pressure

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 14-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 14-1
Contamination Inspection  . . . . . . . . . . . . . . . 14-1
Hydraulic Test & Troubleshooting  . . . . . . . . . 14-1

Charge Pressure Check & Adjust  . . . . . . . 14-1 
Auxiliary Pressure Check & Adjust  . . . . . . 14-3
Drive Pressure Check & Troubleshooting  . 14-4
Posi-Power Check & Adjust  . . . . . . . . . . . 14-5 

15. Troubleshooting

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 15-1
Personal Safety  . . . . . . . . . . . . . . . . . . . . . . 15-1
Visual Inspection . . . . . . . . . . . . . . . . . . . . . . 15-1
Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . 15-1

16. Lubricant and Fuel Specifications

Chapter Overview  . . . . . . . . . . . . . . . . . . . . . 16-1
Fluids & Fuel Specifications  . . . . . . . . . . . . . 16-1

17. Service Aids and Supplements

General Torque Specifications  . . . . . . . . . . . 17-1

Electrical Schematic  . . . . . . . . . . . . . . . . . . . 17-2

Hydraulic Schematic  . . . . . . . . . . . . . . . . . . . 17-3

Rubber Track Utility Vehicle

Table of Contents

II

https://tractormanualz.com/

Summary of Contents for SC50 Scout
















































































































Reviews:

No comments

Related manuals for SC50 Scout

Panasonic LP-M Series Maintenance Manual preview
LP-M Series
Brand: Panasonic Pages: 174
JBL Synthesis SDEC-3000 Calibration Manual preview
Synthesis SDEC-3000
Brand: JBL Pages: 24
Xilica Audio Design XP series User Manual preview
XP series
Brand: Xilica Audio Design Pages: 30
unios Echo Quick Installation Manual preview
Echo
Brand: unios Pages: 2
olympia electronics GR-940/15L Quick Start Manual preview
GR-940/15L
Brand: olympia electronics Pages: 4
Parkside PFMR 1400 A1 Original Operating Instructions preview
PFMR 1400 A1
Brand: Parkside Pages: 58
Veit Brisay BX 1000 Handbook preview
BX 1000
Brand: Veit Brisay Pages: 18
Monosem Wingfold User Manual preview
Wingfold
Brand: Monosem Pages: 104
Stahls Thermo-GRIP Instructions For Using preview
Thermo-GRIP
Brand: Stahls Pages: 2
Otto Bock 21Y105 Instructions For Use Manual preview
21Y105
Brand: Otto Bock Pages: 44
Karma LED PAR27 Instruction Manual preview
LED PAR27
Brand: Karma Pages: 12
p-light Hydro 880 Installation And Instructions For Use preview
Hydro 880
Brand: p-light Pages: 28
Cardin Elettronica RCQ486W00 Manual preview
RCQ486W00
Brand: Cardin Elettronica Pages: 56
Tascam DP-34 Schematic Diagram preview
DP-34
Brand: Tascam Pages: 32
Danfoss S 22 Instructions For Installation And Use Manual preview
S 22
Brand: Danfoss Pages: 20
Coltene ParaPost XT P-680T Instructions For Use Manual preview
ParaPost XT P-680T
Brand: Coltene Pages: 44
Reebok ASTRORIDE A6.0 BIKE User Manual preview
ASTRORIDE A6.0 BIKE
Brand: Reebok Pages: 23
Moog GAT Rotopack BAT Operating Instructions Manual preview
GAT Rotopack BAT
Brand: Moog Pages: 27

Brands by name

Popular brands

Load more brands