manualshive.com logo in svg

Associated Research 3030D, Operation And Service Manual, Page: 26 / 43

Share
Download
Associated Research 3030D Operation And Service Manual Download Page 26

 

OPERATION

 

 

 

22 

OPERATION  INSTRUCTIONS  FOR  HYAMP jr. 

Model 3030D 

 
A.  POWER UP:

 

Check to be sure that the correct input line voltage has been selected on the rear panel, 
either 115 volts AC or 230 volts AC.  Connect the power-input plug into its socket on the 
rear panel of the instrument.  Connect the male end of the plug to the outlet receptacle. 

 
Please be sure that the safety ground on the power line cord is not 
defeated and that you are connecting to a grounded power source.  Also 

connect the rear panel chassis ground for additional safety. 
 
Turn on the POWER switch located on the lower left-hand side of the front panel.  Upon 
powering the instrument up a POWER ON SELF-TEST (POST) will be automatically 
performed.  This test will check for the condition of the ram chips, led indicators, PCBs 
and other critical components. In addition the display will show the following message. 
 

     ARI     HYAMP   JR. 
 3030D        VER :   X.X 

 
The instrument will recall the last memory program that was active and the display will 
show the parameters that were programmed into that memory.  The instrument is now 
ready for operation. 
 

B.   SETUP PROCEDURE: 
1. Output Current Setting

 

Please press the SET key, the display will show:   
 

CURRENT = XX.XA 

 

 
Please use the Up (

∧

) or Down (

∨

) arrow keys to adjust the Current setting, then press the 

EXIT key to store the current setting and return to the Run mode, or press the SET key to 
advance to the next parameter.  The maximum current which may be entered is 30.0 
Amps.  Any value above this will produce an ERROR message.  
 

2. High Limit Setting

 

Please press the SET key until arriving at the HI-LMT setting.  The display will show: 

 

HI-LMT    =   XXX   m

Ω

 

 

 
Please use the Up (

∧

) or Down (

∨

) arrow keys to adjust the value of the High Limit 

resistance trip point then press the EXIT key to store the setting and return to the Run 
mode, or press the SET key to advance to the next parameter.  The unit of measure is in 

CAUTION 

Summary of Contents for 3030D












































Reviews:

No comments