76
STAY MODE ENTRY DELAY to OUTPUT
STAY MODE ENTRY DELAY to OUTPUT -
P162E 1-16E
Option 1 - Output 1
Option 5 - Output 5
Option 2 - Output 2
Option 6 - Output 6
Option 3 - Output 3
Option 7 - Output 7
Option 4 - Output 4
Option 8 - Output 8
If Stay Mode is Armed and a delay zone triggers the entry delay it can also beep an Output to warn that the entry delay is
counting down and the alarm should be turned off.
SENSOR-WATCH TIME
SENSOR-WATCH TIME -
P163E 1-16E (Value 0-9999 Minutes)
If the zone is programmed as a “Sensor-Watch” zone (P124E3E) and it is not operated within the time set at this location
a “Sensor-watch” alarm will be generated. If a detector has this option turned on and it doesn’t operate when disarmed,
this timer will start to count down for the zone/s concerned. The timer is stopped when the area assigned to the zone/s is
armed and resumes with the saved value when disarmed again. The timer is reset back to the original value every time
the zone operates while disarmed.
LEARN RADIO ZONE CODES
LEARN RADIO ZONE CODES
- P164E 1-16E
A RADIO Zone must be enrolled into the panel before it can be used.
To learn a Radio Zone you must first have a compatible receiver connected to the panel keypad buss. With the receiver
connected and the panel in program mode, entering P164E then the zone number you wish to enrol, eg 5E for zone 5, the
keypad will start to beep to indicate that learn mode has been started and the LED on the receiver will flash. Now operate
the detector you wish to learn into Zone 5 slot. Once the transmitted code has been received by the panel and saved, the
keypad will stop beeping and the LED on the receiver will stop flashing.
When learning a new radio zone the panel checks all possible locations (including pendants) before saving the new code
to ensure that the code has not already been loaded into another slot. If the code already exists, the keypad will indicate
which slot the code is already installed at. A number from 1-16 indicates a zone slot and a number from 21-100 indicates
a user slot.
DELETE a RADIO ZONE CODE
DELETE a RADIO ZONE CODE
- P165E 1-16E
If you wish to delete a single Radio Zone, pressing P165E then the Zone number while in Program Mode will delete the
stored code against that Zone, eg P165E 5E will remove the code stored for Zone 5.
FIND a ZONE LOCATION
FIND a RADIO ZONE LOCATION
- P166E 0E
If you have a Radio detector loaded into the panel but are unsure which location (Zone #), pressing P166E then 0E while
in Program Mode on an LED Keypad will start “Find” Mode. There is no need to press 0E when using an LCD keypad
because the keypad will give you written prompts after entering P166E. The keypad will start to beep to indicate that
“Find” mode has been started and the LED on the Receiver will flash. Now operate the Radio Detector you wish to find. If
the Radio Detector is in memory the keypad will display the number (1-16 indicates a zone, and 21-100 indicates a user).
The keypad will stop beeping and the LED on the Receiver will stop flashing.
ZONE NEAR ALARM to OUTPUT
ZONE NEAR ALARM to OUTPUT -
P167E 1-16E
Option 1 - Output 1
Option 5 - Output 5
Option 2 - Output 2
Option 6 - Output 6
Option 3 - Output 3
Option 7 - Output 7
Option 4 - Output 4
Option 8 - Output 8
If zones are programmed for near and confirmed alarms (P64E option 1 on), it is also possible to get an indication of a
Near Alarm from any of the 8 Outputs using this program location. A Near Alarm is the first alarm during an armed
period.
Summary of Contents for Avolution S series
Page 119: ...119...
