Assa Abloy Avolution S series, Installation & Programming Manual

Page: 95 / 119

95
(applies if the User Type, P2E, is set to 1)
Delete a Specific Radio Pendant Code
P19E 21-100E Delete a Specific Radio Pendant Code for Users 21-100
Page 43
(applies if the User Type, P2E, is set to 1)
Find Radio Pendant memory Location
P20E 0E Enter this address then operate the Radio Pendant to find its user #
Page 44
(applies if the User Type, P2E, is set to 1). Only press 0E when using LED Keypad.
Learn Access Tag/Card Codes
P21E 1-100E Learn Access Tag/Card Codes for Users 1-100
Page 44
(applies if the User Type, P2E, is set to 2, 3 or 4)
Delete a Specific Access Tag/Card Code
P22E 1-100E Delete a Specific Access Tag/Card Code for Users 1-100
Page 44
(applies if the User Type, P2E, is set to 2, 3 or 4)
Find an Access Tag/Card memory Location
P23E 0E Enter this address then operate the Access Tag/Card to find its user #
Page 44
(applies if the User Type, P2E, is set to 2, 3 or 4). Only press 0E when using LED Keypad.
MISCELLANEOUS PANEL & CLOCK SETTINGS
Installer Code
P25E 1E Installer Code - ( Default = 000000)
Page 44
Duress Digit
P25E 2E Duress Digit -
Value 1-9 (Default = 0 Duress Function Disabled)
Page 45
Dial Report Delay
P25E 3E Dial Report Delay - Value 0-255 seconds (Default = 0)
Page 45
Radio Detector Supervised Timer
P25E 4E Radio Detector Supervised Timer -
0-9999 Minutes (Default = 60 Minutes)
Page 45
Two Trigger Timer
P25E 5E Two Trigger Timer - Value 0-255 Seconds (Default = 60 Sec)
Page 45
Mains Fail Reporting Delay
P25E 6E Mains Fail Reporting Delay - Value 0-9999 Seconds (Default = 600 Sec)
Page 45
Receiver Fail Delay
P25E 7E Receiver Fail Delay - Value 0-9999 Seconds (Default = 0 Sec-Disabled)
Page 45
Upload/Download Site Code Number
P25E 8E Upload/Download Site Code Number -
Up to
8 Characters (Default = None)
Page 45
Temporary Output Disable
P25E 9E Temporary Output Disable -
Output 1-8
Page 46
Miscellaneous Panel Options
P25E 10E Misc. Panel Options Miscellaneous Options
Page 46
(Default = 1, 2, 6) 1 = Panel Tamper is 2k2 EOL
2 = Direct access to program mode for the installer code.
3 = Disable Mains Fail Test
4 = Listen-in to O/P # 1 Low Volume
5 = Receiver Fail/RF Jammed Lockout
6 = Send output information to keypad bus
7 = Cannot arm if the system battery is low
8 = Installer Lockout
Installer Options
P25E 11E Installer Options
Page 47
(Default = All Off) 1 = Entry to installer mode resets confirmed alarms
2 = Entry to installer mode resets tamper alarms
3 = Entry to installer mode resets low battery alarms
4 = Entry to installer mode resets supervisory alarms
5 = Cannot Arm if there is a keypad Fault
6 = Cannot Arm if there is a Telephone Line Failure or Comms Fault
7 = 10 Incorrect Code Attempts locks out the keypad for 90 Seconds
8 = User Codes Must be 4-6 digits long
User Options
P25E 12E User Options (NOTE: This Option can ONLY be accessed from Client Mode)
Page 47
(Default = All Off) 1 = Hide User Codes from Installer