manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 4

 

3.3 Username and Password................................................................................................................................22

 

3.5 Restoring Factory Defaults..................................................................................................................................... 23

 

Chapter 4: Understanding the Command Line Interface (CLI) ..................................................................................... 24

 

4.1 User Top (User EXEC) Mode................................................................................................................................. 24

 

4.2 Privileged Top (Privileged EXEC) Mode ................................................................................................................ 25

 

4.3 Global Configuration Mode..................................................................................................................................... 27

 

4.3.1 Interface Configuration Mode.......................................................................................................................28

 

4.4 Advanced Features Supported within the Command Mode ................................................................................... 29

 

4.5 Using CLI Command History.................................................................................................................................. 31

 

4.6 Using Command-Line Editing Features and Shortcuts .......................................................................................... 32

 

4.6.1 Moving Around on the Command Line.........................................................................................................32

 

4.6.2 Completing a Partial Command Name.........................................................................................................33

 

4.6.3 Deleting Entries............................................................................................................................................33

 

 

Chapter 5: Managing the System and Configuration Files……………………………………………...…………………...34

 

5.1 Managing the System 34

 

5.1.1 Setting the System Clock .............................................................................................................................34

 

5.1.2 Specify the Hostname ..................................................................................................................................35

 

5.1.5 Test Connections with Ping Tests................................................................................................................35

 

5.1.3 Enable the System Log ................................................................................................................................35

 

5.1.4 Displaying the Operating Configuration........................................................................................................35

 

5.2 Managing Configuration Files................................................................................................................................. 36

 

5.2.1 Configuring from the Terminal......................................................................................................................36

 

5.2.2 Copying Configuration Files to a Network Server ........................................................................................36

 

5.2.3 Copying Configuration Files from a Network Server to the Switch...............................................................37

 

5.3 Managing system image Files................................................................................................................................ 38

 

5.3.1 Saving System image to a Network Server..................................................................................................38

 

5.3.2 Replacing System image  from a Network Server........................................................................................38

 

5.4 Configuring SNMP ................................................................................................................................................. 38

 

5.4.1 Configuring SNMP Support..........................................................................................................................39

 

5.5 Spanning Tree Algorithm ....................................................................................................................................... 40

 

4 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands