manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 135

 

Mode 

Interface Config 

10.5.7 admin-mode 

Configure administrative mode on a port 

Format 

Switch(Interface 1)# admin-mode {enable|disable} 

Mode 

Interface Config 

10.5.8 auto-negotiate 

45 
Configure auto-negotiate mode on a port 

Format 

auto-negotiate {enable|disable} 

Mode 

Interface Config 

10.5.9 speed 

Set port speed to 10Mbps half duplex/ 10Mbps full/ 100Mbps half/ 100Mbps 
full/ 1000Mbps 100FX mode/1000base-x full . 

Format 

speed {10hd|10fd|100hd|100fd|1000fd|100fx|1000base-x} 

Mode 

Interface Config 

10.5.10 flow-control command 
flow-control enable 

This command enable flow-control at port. 

Format 

flow-control {enabledisable} 

Mode 

Interface Config 

10.5.11 port-security command 
1)port-security 

This command add or delete a static mac into mac security table. 

Format 

port-security {add|delete} <

sourcemac 

> 

Mode 

Interface Config 

2)port-security lock-mode 

This command enable/disable port security. 

Format 

port-security lock-mode {none|static} 

Mode 

Interface Config 

port-security lock-mode dynamic 

This command enable limited dynamic lock mode,and specify maximin 
learning entries for limited dynamic lock mode.the max-entries value :0~25. 

Format 

port-security lock-mode dynamic max-entries 24 

Mode 

Interface Config 

10.5.12 qos command 

This command specifies port-based qos. 

Format 

qos port-based status {enable|disable} 

Mode 

Interface Config 

10.5.13 rate-limit command 
10.5.13.1 rate-limit Egress 

This command limits egress rate, which the unit is Kbps. 

Format 

rate-limit egress <

rate

> 

Mode 

Interface Config 

10.5.13.2 rate-limit Ingress 

This command limits ingress rate, which the unit is Kbps. 

Format 

rate-limit ingress <

rate

> 

Mode 

Interface Config 

10.5.14 storm-control command 
10.5.14.1 storm-control 

Enable/disable storm control. 

Format 

storm-control disable 

Mode 

Interface Config 

46 

10.5.14.2 storm-control broadcast 

This command storm control for broadcast only, and limited 
value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps 

135 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands