manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 112

 

This command is used to exit current shell 

Format 

logout 

Mode 

Privileged Mode 

10.3.8 ping 

This command is used to proceed ping destination host 

Format 

ping <

A.B.C.D

> 

Mode 

Privileged Mode 

10.3.9 reload 

This command is used to reboot system 

Format 

reload 

Mode 

Privileged Mode 

17 

10.3.10 save 

This command is used to save configuration 

Format 

save 

Mode 

Privileged Mode 

10.3.11 show 

This command is used to show configured data 

10.3.11.1 show qos 

This command display class of service information 

1) show qos cos 

This command display the cos mapping 

Format 

show qos cos 

Mode 

Privileged Mode 

2) show qos queue-settings 

This command display the queue-settings mapping 

Format 

show qos queue-settings 

Mode 

Privileged Mode 

3) show qos advanced 

This command display qos advanced mode information 

show qos advanced mode 

This command display mode of qos 

Format 

show qos advanced mode 

Mode 

Privileged Mode 

show qos advanced dscp 

This command display qos dscp mapping 

Format 

show qos advanced dscp 

Mode 

Privileged Mode 

show qos advanced ip-precedence 

This command display qos ip precedence mapping 

Format 

show qos advanced ip-precedence 

Mode 

Privileged Mode 

4) show qos port-based 

This command is used to display class of service information 

show qos port-based port 

This command display class of service information 

Format 

show qos port-based port <

port-ID

> 

Mode 

Privileged Mode 

show qos port-based all 

This command display all switch interfaces’ cos settings 

Format 

show qos port-based all 

Mode 

Privileged Mode 

10.3.11.2 show dot1x 

This command display dot1x information 
18 

1) show dot1x config 

112 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands