manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 13

 

1.4.1 LEDs 

The IC3624/48 front panel LED display allows you to monitor the status of the switch.  

The IC3624/48 has one power LED indicator. There are also LED indicators for each of the ports. Refer to the 
following table for LED information. 

 

LED

 

 Color

 

 Description

 

Power

 

Green 

Off

 

Power is on. 

Power is off, or main power has failed.

 

1000MBps

 

Amber 

Green 

Off

 

A valid 1000 Mbps link has been established on the port. 

A valid 10/100 Mbps link has been established on the port. 

No link has been established on the port.

 

100MBps Green 

Off

 

A valid 10/100 Mbps link has been established on the port. 

No link has been established on the port.

 

Link/Activity

 

Green 

Blinking Green 

Off

 

A link has been established on the port. 

Activity has been detected. 

No link has been established on the port.

 

 

1.5 Management and Configuration 

The switch is managed using Command Line Interface (CLI) in order to access several different command modes. 
Entering a question mark (?) at each command mode’s prompt provides a list of commands. 

1.5.1 Console Interface 

Support for local, out-of-band management is delivered through a terminal or modem attached to the EIA/TIA-232  
interface. You can access the switch by connecting a PC or terminal to the console port of the switch, via a serial 
cable. The default uername/ password set on the console line is admin/

Asante

 (it is case-sensitive). The default IP 

address is 

192.168.0.1

.  It can be modified to suit your network setup. See 3.4 for details. 

Remote in-band management is available through Simple Network Management Protocol (SNMP) and Telnet client. 
When connecting via a Telnet session, the default login/password is also 

admin

/

Asante 

(case-sensitive). 

 

See Chapter 2 for more information on connecting to the switch. 

13 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands