manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 129

 

10.4.110.8 spanning-tree mst 

Configure a multiple spanning tree instance. 

1) spanning-tree mst instance 

This command creates or removes a MST instance 

spanning-tree mst instance add 

This command creates a MST instance. 

Format 

spanning-tree mst instance add vlan <

vlan list

> mstpid <

MST ID

> 

Mode 

Global Config 

e.g. Switch(Config)# Spanning-Tree mst instance add vlan 2-5 mstpid 2 
Switch(Config)# Spanning-Tree mst instance add vlan 6 mstpid 3 

spanning-tree mst instance delete 

This command removes the last MST instance. 

Format 

spanning-tree mst instance delete 

Mode 

Global Config 

2 )spanning-tree mst vlan 

This command adds or deletes vlan frome a MSTP instance. 

spanning-tree mst vlan <MST ID> <vlan list> add 

This command creates a MST instance. 

Format 

spanning-tree mst vlan <

MST ID

> <

vlan list

> add 

Mode 

Global Config 

e.g. Switch(Config)# Spanning-Tree mst vlan 3 3-5 add 

Spanning-Tree mst vlan <MST ID> <vlan list> delete 

This command deletes a vlan from a MST instance. 

Format 

Spanning-Tree mst vlan <

MST ID

> < vlan 

list

> delete 

Mode 

Global Config 

38 

3) spanning-tree mst bridgepri 

This command configures bridge priority for a MST instance. 

Format 

spanning-tree mst bridgepri <

MST ID

> <

priority

> 

Mode 

Global Config 

4) spanning-tree mst cost 

This command configures port path cost in a MST instance. 

Format 

spanning-tree mst cost <

MST ID

> <

path cost

> ports <

port list

> 

Mode 

Global Config 

5)spanning-tree mst priority 

This command configures port priority in a MST instance 

Format 

spanning-tree mst priority <

MST ID

> <

priority

> ports <

port list

> 

Mode 

Global Config 

10.4.20 User commands 

This command changes user password. 

Format 

user password 

Mode 

Global Config 

10.4.21 Interface commands 

This command enters into configure interface mode. 

Format 

Interface <

port-ID

> 

Mode 

Global Config 

10.4.22 rmon 

This command is used to configure RMON. 

10.4.22.1 rmon event 

This command creates rmon event entry. 

Format 

rmon event index < 

1..65535 

> desc <

WORD

> event <

1..4

> 

community <

WORD

>owner<

WORD

> 

Mode 

Global Config 

e.g. Switch(Config)# rmon event index 1 desc 123 event 4 community 123 
owner test 

10.4.22.2 rmon alarm 

129 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands