manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 120

 

10.4.7 Log 

This command is used to configure log server 

10.4.7.1 Log log-server 

This command is used to configure log server 

1) Log log-server name <WORD>add 

This command is used to specify log server name, enter a name, up to 12 
characters, add a log server IP address 

Format 

Log log-server name <

WORD

> add ipaddr word 

Mode 

Global Config 

2) Log log-server name <word> delete 

This command is used to delete a log server 
27 

Format 

log log-server name <

WORD

> delete 

Mode 

Global Config 

10.4.7.2 Log logging-target 

This command is used to configure log notification level 

1) log logging-target memory 

This command is used to specify memory log notify-level 

Format 

log logging-target memory {enable|disable} 

Mode 

Global Config 

2) log logging-target flash 

This command is used to specify flash log notify-level 

Format 

log logging-target flash {enable|disable} 

Mode 

Privileged Mode 

3) log logging-target console 

This command is used to specify console log notify-level 

Format 

log logging-target console {enable|disable} 

Mode 

Global Config 

4) log logging-target server 

This command is used to specify console log notify-level 

Format 

log logging-target server name <

WORD

> {enable|disable} 

Mode 

Global Config 

10.4.8 radius-server 

This command is used to configure radius server 

Format 

radius-server ip <

IP addr

> 

Mode 

Global Config 

10.4.9 static-address 

This command is used to specify static address 

10.4.10.1 static-address add 

This command is used to add static mac address 

Format 

static-address add <

mac addr

> vid <

vlan-ID

> port <

port-ID

> 

Mode 

Global Config 

10.4.10.2 static-address delete 

This command is used to delete static mac address 

Format 

static-address delete <mac 

addr

> vid <vlan

-ID

> 

Mode 

Global Config 

10.4.10 mgmt-accesslist commands 
10.4.10.1 mgmt-accesslist ipaddr 

This command specifies a management access IP for the DUT, up to 8 IP 
address can be set. 

Format 

mgmt-accesslist ipaddr <

IP addr

> 

Mode 

Global Config 

10.4.10.2 mgmt-accesslist enable 

This command enables management access list. Only the IP address 
specified in the management list is allowed to access DUT. 

Format 

mgmt-accesslist enable 

120 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands