manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 124

 

Format 

port-all Storm-Control broadcast-multicast <

value

> 

Mode 

Global Config 

4) port-all storm-control broadcast-unknown 

This command configures storm control for broadcast and unknown unicast. 

Format 

port-all storm-control broadcast-unknown <

value

> 

Mode 

Global Config 

5) port-all storm-control all-cast 

This command configures storm control for broadcast, multicast and unknown 
unicast. 

Format 

port-all Storm-Control all-cast <

value

> 

Mode 

Global Config 

10.4.15 qos commands 
10.4.15.1 qos qos-advanced 

Configure qos advanced mode. 

1) qos qos-advanced DSCP 

This command enables DSCP mode. 

Format 

qos qos-advanced DSCP 

Mode 

Global Config 

2) qos qos-advanced ip_precedence 

This command enables IP Precedence mode. 

Format 

qos qos-advanced ip_precedence 

Mode 

Global Config 

3) qos qos-advanced none 

This command disables qos advanced mode. 

Format 

qos qos-advanced none 

Mode 

Global Config 

32 

10.4.15.2 qos cos 

This command configures 802.1p priority queue mapping. 

Format 

Qos cos priority <0-7> queue <1-4> 

Mode 

Global Config 

10.4.15.3 qos dscp 

This command specifies dscp value to queue mapping. 

Format 

Qos dscp <0-63> queue <1-4> 

Mode 

Global Config 

10.4.15.4 qos port-based 

This command configures port-based priority mapping. 

Format 

qos port-based port <

WORD

>status {enable | disable} 

Mode 

Global Config 

10.4.15.5 qos scheduling 

Configure qos scheduling mode. 

1) qos scheduling strict 

This command sets to strict priority. 

Format 

qos scheduling strict 

Mode 

Global Config 

2) qos scheduling wrr 

This command sets to Weight Round-Robin. 

Format 

qos scheduling wrr 

Mode 

Global Config 

10.4.15.6 qos ip-precedence 

This command configures IP precedence queue mapping. 

Format 

qos ip-precedence <0-7> queue <1-4> 

Mode 

Global Config 

10.4.15.7 qos wrr 

This command configures queue weight for weight round robin. 

Format 

qos wrr weight <1-15> queue <1-4> 

124 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands