Asante IntraCore 3624 User Manual Download Page 123

Page: 123 / 145

This command configures ports auto-negotiation mode.

Format

port-all auto-negotiate {enable|disable}

Mode

Global Config

10.4.14.3 port-all flow-control

This command configures ports flow control.

Format

port-all flow-control {enable|disable}

Mode

Global Config

10.4.14.4 port-all portsec-lockmode

Configure port security.

1) port-all portsec-lockmode none

This command disable port security.

Format

port-all portsec-lockmode none

Mode

Global Config

2) port-all portsec-lockmode static
Note:

This commands only support on G24-PORTS 100 2 GIGABIT

COMBO PORTS LAYER 2 MANAGEMENT SWITCHL/ G48 100 4
GIGABIT COMBO WITH 2 SHARED MINI-GBIC SLOTS LAYER 2+
MANAGEMENT SWITCH.
This command enable static lock mode.

Format

port-all portsec-lockmode static

Mode

Global Config

3) port-all portsec-lockmode dynamic

This command enable limited dynamic lock mode.

Format

port-all portsec-lockmode dynamic max-entries <0-24>

Mode

Global Config

10.4.14.5 port-all rate-limit

Configure rate limit value on all ports.

1)port-all rate-limit egress

This command specifies egress rate limit.

Format

port-all Rate-Limit egress <

value

Mode

Global Config

2)port-all rate-limit ingress

This command specifies ingress rate limit.

Format

port-all rate-limit ingress <

value

Mode

Global Config

10.4.14.6 port-all rmon-counter

This command configures rmon counter capability on ports.

Format

port-all rmon-counter {enable|disable}

Mode

Global Config

10.4.14.7 port-all speed

This command configures ports speed.

Format

port-all speed {10hd|10fd|100hd|100fd}

Mode

Global Config

10.4.14.8 port-all storm-control

Configure all ports’ storm control settings.

1) port-all storm-control disable

This command disables storm control.

Format

port-all Storm-Control disable

Mode

Global Config

2) port-all storm-control broadcast

This command configures storm control for broadcast only.

Format

port-all storm-control broadcast <

value

Mode

Global Config

3) port-all storm-control broadcast-multicast

This command configures storm control for broadcast and multicast.

123

Asante IntraCore IC3624/48

User’s Manual

Summary of Contents for IntraCore 3624


















































































































































Search results

Summary of Contents for IntraCore 3624

Reviews:

Brands by name

Popular brands

Asante IntraCore 3624, User Manual

Search results

Summary of Contents for IntraCore 3624

Reviews:

Brands by name

Popular brands