manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 127

 

Mode 

Global Config 

snmp trapstation add <ip-addr> community <community name> type 
none 

Send no trap. 

Format 

snmp trapstation add <

ip-addr

> community <

community name

> type 

none trap-version {1-2} 

Mode 

Global Config 

2) snmp trapstation delete 

This command delete a trap station. 

Format 

snmp trapstation delete <

WORD

> 

Mode 

Global Config 

10.4.18 sntp commands 
10.4.18.1 sntp daylight 

This command enables or disables the daylight saving configuration. 

Format 

sntp daylight {enable|disable} 

Mode 

Global Config 

10.4.18.2 sntp localtime 

Configure the local time. 

1) sntp localtime enable 

This command enables local time. 

Format 

sntp localtime enable 

Mode 

Global Config 

2) sntp localtime localtime_date 

This command sets local time. 

Format 

sntp localtime localtime_date <

year

> <

month

> <

date

> <

hour

> 

<

minute

> <

second

> 

Mode 

Global Config 

10.4.18.3 sntp server 
1) sntp server enable 

This command enables sntp server. 

Format 

sntp server enable 

Mode 

Global Config 

2) sntp server ipaddr 

This command sets sntp server IP address. 

Format 

sntp server ipaddr <

IP-addr

> 

Mode 

Global Config 

3) sntp server polling 

This command sets sntp server polling time interval. 

Format 

sntp serve polling <

0-9

> 

Mode 

Global Config 

10.4.18.4 sntp timezone 

This command sets sntp timezone. 

Format 

sntp timezone <1-75> 

Mode 

Global Config 

10.4.19 spanning-tree commands 

36 

10.4.110.1 spanning-tree forceversion 

This command configures Spanning Tree protocol version. 

1) spanning-tree forceversion 8021s 

This command selects spanning tree type as 8021.s(multiple Spanning Tree). 

Format 

spanning-tree forceversion 8021s 

Mode 

Global Config 

2) spanning-tree forceversion 8021w 

This command selects spanning tree type as 802.1w(rapid Spanning Tree). 

Format 

spanning-tree forceversion 8021w 

Mode 

Global Config 

127 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands