manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 121

 

Mode 

Global Config 

28 

10.4.10.3 mgmt-accesslist disable 

This command disables management access list. 

Format 

mgmt-accesslist disable 

Mode 

Global Config 

10.4.11 monitor commands 
10.4.11.1 monitor enable 

This command enables port mirroring. 

Format 

monitor enable 

Mode 

Global Config 

10.4.11.2 monitor disable 

This command disables port mirroring. 

Format 

monitor disable 

Mode 

Global Config 

10.4.11.3 monitor des 

Configure destination port. 

1) monitor des <port-ID> probetype bidirection 

This command configures port monitor probetype as bi-direction traffic. 

Format 

monitor des <

port-ID

> probetype bidirection src <

port list

> 

Mode 

Global Config 

e.g. Switch(config)# monitor des 1 probetype bidirection src 2-8 

2) monitor des <port-ID> probetype ingress 

This command configures port monitor probetype as ingress traffic. 

Format 

monitor des <

port-ID

> probetype ingress src <

port list

> 

Mode 

Global Config 

e.g. Switch(config)# monitor des 1 probetype ingress src 2-8 

3) monitor des <port-ID> probetype egress 

This command configures port monitor probetype as egress traffic. 

Format 

monitor des <

port-ID

> probetype egress src <

port list

> 

Mode 

Global Config 

e.g. Switch(config)# monitor des 1 probetype egress src 2-8 

10.4.12 dot1x commands 
10.4.12.1 dot1x enable 

This command enables global 802.1x function. 

Format 

dot1x enable 

Mode 

Global Config 

10.4.12.2 dot1x disable 

This command disables global 802.1x function. 

Format 

dot1x disable 

Mode 

Global Config 

10.4.12.3 dot1x port-control 

Configure port auto-authentication mode. 

1) dot1x port-control enable 

This command set auto-authorized on a list of ports. 

Format 

dot1x port-control enable port <

port list

> 

Mode 

Global Config 

2) dot1x port-control disable 

This command set force authorized on a list of ports. 

Format 

dot1x port-control disable port <

port list

> 

Mode 

Global Config 

29 
e.g. Switch(config)# dot1x port-control disable port 1-4 

10.4.13 network commands 
10.4.13.1 network mgmt-vlan 

This command changes management vlan. 

121 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands