manualshive.com logo in svg

Asante IntraCore 3624, User Manual

Share
Download
Asante IntraCore 3624 User Manual Download Page 131

 

This command clears TCP/UDP destination port filter. 

Format 

access-list name <

WORD

> clear l4port DST port 

40 

Mode 

Global Config 

4) access-list name <WORD> clear packet-type 

This command clears packet type filter. 

Format 

access-list name <

WORD

> clear packet-type 

Mode 

Global Config 

5) access-list name <WORD> clear mac SA 

This command clears a source mac address. 

Format 

Access-list name <

WORD

> clear mac SA 

Mode 

Global Config 

6) access-list name <WORD> clear MAC DA 

This command clears a destination mac address. 

Format 

Access-list name <

WORD

> clear mac DA. 

Mode 

Global Config 

7)access-list name <WORD> clear VID 

This command clears the 802.1Q VLAN tag of packet. 

Format 

Access-list name <

WORD

> clear VID 

Mode 

Global Config 

8)access-list name <WORD> clear ether-type 

This command clears ether type filter. 

Format 

access-list name <

WORD

> clear ether-type 

Mode 

Global Config 

10.4.23.4 access-list name <WORD> deletes. 

This command removes the ACL entry. 

Format 

access-list name <

WORD

> deletes 

Mode 

Global Config 

10.4.23.5 access-list name <WORD> {enable|disable} 

This command enables/disables the ACL entry. 

Format 

access-list name <

WORD

> {enable|disable} 

Mode 

Global Config 

10.4.23.6 access-list name <WORD> set 
1) access-list name <WORD> set priority 

This command specifies ACL entry priority. 

Format 

access-list name <

WORD

> set priority <0-65535> 

Mode 

Global Config 

2) access-list name <WORD> set IP-mode 
access-list name <WORD> set IP-mode SRC IP. 

This command specifies a source IP address. 

Format 

access-list name <

WORD

> set IP-mode SRC IP <IP-addr> 

<

mask-addr

> 

Mode 

Global Config 

access-list name <WORD> set IP-mode DST IP 

This command specifies a destination IP address. 
41 

Format 

access-list name <

WORD

> set IP-mode DSP IP <

IP-addr

> 

<

mask-addr

> 

Mode 

Global Config 

3) access-list name <WORD> set L4port 

This command specifies the TCP/UDP port range. 

access-list name <WORD> set l4port SRC-port 

This command specifies the source TCP/UDP port range. 

Format 

Access-list name <

WORD

> set L4 port SRE-port from <1-65535> 

to <1-65535> 

Mode 

Global Config 

131 

Asante IntraCore IC3624/48

 

User’s Manual

 

 

Summary of Contents for IntraCore 3624


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands