background image

 
 

 

1-2) Replacement of Reamer Blade 

 

 
 
 
 
 
 
(1)

 

Lift the Cutter and Die-Head and down the Reamer. 

(2)

 

Put out the Spring Pin in the neck of the Reamer Blade.   

(3)

 

The Reamer Blade is detached by pulling the Reamer Shaft forward. 

(4)

 

Install a new Reamer Blade. 

(5)

 

Re-insert the removed Spring Pin in the hole of a new Reamer Blade. 

 
 
 

1-3) Replacement of Cutter Blade 

  (1) Swing the Cutter to upright position and lower the Die-Head. 
  (2) Straighten the bend of split pin and pull it upward. (fig.38) 
  (3) While holding the Blade, slightly push out the Cutter Blade Set Pin and pull out from the opposite side.   
          (fig.39) 
  (4) Do not lost a washer beside of Cutter Blade. 

 

 

 

 

 

 

 

 

 

(5) Wipe off chips, dirt, oil, etc. from the pin and apply grease to the groove. 
(6)

 

Put a new Blade into the Blade Bracket, washer is put in the side of the Cutter Blade (split Cutter 
Pin side), and insert pin. 

(7) Insert a new split pin into the Cutter Blade Set Pin, and end the ends.

 

       

 

 

27 

 

 

 

Wear gloves when working so as not to cut fingers with the Reamer Blade. 

 

 

39

38

Cutter Blade

 

Cutter Blade Set Pin 

Wear gloves

 

Pull out 
split pin

 

Split Pin

 

Summary of Contents for Beaver 100





































Reviews: