ARRI ARTEMIS 2 User Manual Download Page 5

Page: 5 / 93

Content

8.3.3

Gimbal Clamp Force Adjustment................................................................................. 62

8.4

Master Grip Trinity Installation and Operation................................................................63

8.4.1

Mounting the Master Grip TRINITY on the Gimbal......................................................63

8.4.2

Mounting a Monitor Mount on the Master Grip TRINITY............................................. 64

8.4.3

Mounting Transvideo Starlite Monitor...........................................................................65

8.4.4

Mounting Small HD 503 Monitor.................................................................................. 66

8.4.5

Positioning of the Master Grip TRINITY.......................................................................67

8.5

RCP-3 Installation and Operation...................................................................................68

8.5.1

RCP-3 Installation.........................................................................................................68

8.5.2

Power ON / OFF...........................................................................................................68

8.5.3

Jog-Wheels................................................................................................................... 69

8.5.4

Radio Module................................................................................................................69

8.6

TST and BST Installation and Operation....................................................................... 70

8.6.1

Installing TST/BST to Center Post............................................................................... 70

8.6.2

Installing SAM dovetail plates...................................................................................... 71

8.6.3

Adjusting Clamping Force............................................................................................ 73

8.7

Battery Hanger Module Operation and Installation........................................................ 74

8.7.1

Batter Hanger Module BHM-2......................................................................................74

8.7.2

Mounting ø19mm Rods................................................................................................ 74

8.7.3

Battery Mounting System............................................................................................. 75

8.7.4

Battery Hanger Module.................................................................................................75

8.7.5

Connecting the Battery Mounts to the Battery Hanger Module....................................76

8.7.6

Connecting the Battery Hanger Module to the Top / Bottom Stage............................. 77

8.7.7

Power ON / OFF...........................................................................................................77

8.7.8

Jog-Wheel Functions.................................................................................................... 78

8.7.9

TRINITY / ARTEMIS Mode...........................................................................................78

8.7.10

Battery Status............................................................................................................... 79

8.7.11

General Working Method / BHM-2............................................................................... 81

8.7.12

Discharge Modes..........................................................................................................82

8.7.13

System BHM-2

...................................................................................................................................... 84

8.8

Battery Mounting System Operation and Installation..................................................... 87

8.8.1

Installation and Replacement of Battery Mounts..........................................................87

8.8.2

Mounting the BMS on rods.......................................................................................... 87

Cleaning and Repair.......................................................................................................88

9.1

Cleaning Instructions...................................................................................................... 88

9.2

Repair..............................................................................................................................88

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands