ARRI ARTEMIS 2 User Manual Download Page 55

Page: 55 / 93

Installation and Operation

CAUTION

Automatically move to the home position

Risk of crushing fingers. The camera / tilt and roll axis will automatically move to the home

position, after turning on the stabilization.

Make sure that your fingers do not get between the top cover and the camera while checking the

tilt axis.

Main Power On

1. Bring the switcher into the

position.

ATTENTION

After switching on, the TRINITY-2 head is supplied with 24V, camera, monitor, accessories are

supplied with 12V and 24V, depending on the case.

The

motors are not yet active

as long as the

Stabilizer

is set to

OFF

As long as the

Stabilizer

OFF

, you can work on the camera setting.

Stabilizer ON

2. Turn the

Stabilizer ON

, when the camera preparation is complete.

→ Observe the camera after turning on the stabilization, the camera

Tilt

and

Roll

axis will automatically move to the

Home Position

Onboard GUI

3. Additional functions can be controlled via the jog-wheel

and read out via the display.

Cable Connections

4. Connect the joystick cable and video cable with the

Master Grip TRINITY and the monitor.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands