ARRI ARTEMIS 2 User Manual Download Page 57

Page: 57 / 93

Installation and Operation

ADVICE

If the clamping force of the Center Post clamp weakens,

clean

the Inner Post with isopropanol,

before you adjust the clamping force.

Clamp Force Adjustment

1. Open the clamp lever.

2. Turn the silver nut by a 1/8 or 1/4 turn to the right, to adjust the

clamp force.

→ The clamping force is adjusted.

8.3

Gimbal Installation and Operation

8.3.1 Installing the 1.8in Gimbal to the Center Post

Preparation:

Remove the top stage from the center post

Prepare Post Tool (K2.0040046) for Installation

1. Use the

Post Tool

to open the centering ring by turning it to

the left.

2. Open the gimbal clamp lever
3. Put the gimbal on the post.

→ The Gimbal is ready for the positioning on the center post.

Positioning the Gimbal

After the gimbal sits on the post,it can be positioned.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands