ARRI ARTEMIS 2 User Manual Download Page 65

Page: 65 / 93

Installation and Operation

8.4.3 Mounting Transvideo Starlite Monitor

Location pins

1. Remove the location pins.

Monitor Position

2. Place the monitor and bring it in the desired angle.

3. Tighten the screw at the back.

Monitor Power

4. Connect the MTG Monitor Pwr, Lemo 0B, 5pin (K2.0038999) with the

Transvideo / ARRI Starlite monitor and with the

upper

LBUS Socket at

the Master Grip TRINITY.

ATTENTION

If you are using a standard Transvideo Starlite monitor with a 2pin Lemo socket, use the

MTG Monitor Pwr, Lemo 0B, 2pin (K2.0038998).

Joystick Cable

5. Connect the TRINITY 2

Joystick Cable

75cm/29.5in (K2.0043861) with

the

lower

LBUS Socket at the Master Grip TRINITY and with the LBUS

Socket at the TRINITY 2 head.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands