ARRI ARTEMIS 2 User Manual Download Page 77

Page: 77 / 93

Installation and Operation

Left Side

Same procedure with the

BAT IN 2

ADVICE

not

turn the

POWER OUT

Socket!

This socket is fixed and cannot be rotated.

8.7.6 Connecting the Battery Hanger Module to the Top / Bottom Stage

The

POWER OUT

socket of the Battery Hanger provides high capacity 12V and 24V power,

plus digital battery communication to the artemis and TRINITY system as soon the BHM-2

is connected to the Top Stage (TST) or Bottom Stage (BST).

ATTENTION

Hot Plug

Check that the BHM is switched

OFF

before connecting it to the TST / BST.

Connecting an operating BHM to the system, may produce an unwanted electrical surge!

Connect the Power Cable, BHM-2 to TST (K2.0037771)

to the

POWER OUT

socket of the

Battery Hanger Module and the

POWER IN

socket of the Top / Bottom Stage.

8.7.7 Power ON / OFF

To turn the BHM-2 / the entire system

and

OFF

press and hold

down the Jog-Wheel until the ARRI logo appears on the display.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Brands by name

Popular brands