ARRI ARTEMIS 2 User Manual Download Page 73

Page: 73 / 93

Installation and Operation

KK.0038971

Long Stabilizer Mount 15mm Mini/Mini

KK.0038972

Long Stabilizer Mount 19mm Mini/Mini LF

K2.0039089

Compact Lens Support CLS-1

K2.0040036

Balance Utility Dovetail BUD-2

K2.0039861

Dovetail Utility Base DUB-1

K2.0038537

Stabilizer System Bracket SSB-2 19mm

K2.0038618

Stabilizer System Bracket SSB-2 15mm

8.6.3 Adjusting Clamping Force

If the clamping force of the clamping mechanism decreases:

Check that the clamping pads are clean. Remove dirt or grease with isopropanol.

Check whether the clamping pads still cover the entire area. If parts of the clamp pads are gone,

please contact ARRI Service.

ADVICE

Overtighten the leveling screw

This will cause the clamping force to become excessive and the Clamp Pads may be dam-

aged.

Turn the silver nut by a 1/8 or 1/4 turn to the right. NOT more!

Clamp Force Adjustment

1. Open the Clamp Lever.

2. Turn the silver nut by a 1/8 or 1/4 turn to the right, to ad-

just the clamp force.

→ The clamping force is adjusted.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands