ARRI ARTEMIS 2 User Manual Download Page 78

Page: 78 / 93

Installation and Operation

8.7.8 Jog-Wheel Functions

Turning the jog-wheel takes you through the

various status pages.

double click

on the jog-wheel opens

the

menu

There you set up the Battery Hanger

modes or carry out software updates in

the System sub menu.

Modes

and

functions

can be selected

and activated by turning and pressing the
jog-wheel.

8.7.9 TRINITY / ARTEMIS Mode

ADVICE

The BHM-2 offers two different modes:

ARTEMIS

and

TRINITY

Technically and functionally, both modes are exactly the same, they only differ in the way the display

acts.

ARTEMIS

mode, the display is

rotated

180°

as soon as the artemis was moved into the

low

mode

position.

TRINITY

mode, the display will

turn off

as soon as the system is raised

above 40°

in the tilt axis.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands