ARRI ARTEMIS 2 User Manual Download Page 47

Page: 47 / 93

Installation and Operation

WARNING

Falling Camera Accessories

If the system is inadequately built up or assembled, it can fall down and cause serious in-

juries and damage to the system or property.

Installation and operation may only be carried out by trained personnel who are familiar with the

system. Observe accident prevention regulations.

Do not place the system on an unstable trolley or hand truck, stand, tripod, bracket, table or any

other unstable support device.

Always place the camera on dedicated support devices.
Secure the system and its accessories against falling and tipping over. Observe the general and

local safety regulations.

When using the system on camera cranes, a suitable safety rope must be used.
Use only accessories approved by ARRI. The use of accessories not approved by ARRI is at

your own risk. Please observe all relevant safety guidelines.

CAUTION

Improper installation of camera accessories

Crushing hazard for fingers and/or hands.

Before mounting ARRI accessories or recommended third-party accessories (such as lenses,

mechanical accessories, electronic accessories), read the operating instructions provided by the

manufacturer.

Always use the tools specified by the manufacturer for mounting.

CAUTION

Improper vertical adjustment of the camera stabilizer ring

Crushing hazard for fingers and/or hands after opening the clamping levers.

Before mounting the camera stabilizer ring, read the operating instructions provided by the

manufacturer.

The height of the stabilizer ring should always be adjusted by two people
Always use the tools specified by the manufacturer for mounting.

8.1

TRINITY Head Installation and Operation

8.1.1 Installing TRINITY 2 Head

Tilt-Lock

1. Lock the Tilt-Lock first!

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands