ARRI ARTEMIS 2 User Manual Download Page 68

Page: 68 / 93

Installation and Operation

8.5

RCP-3 Installation and Operation

8.5.1 RCP-3 Installation

Mounting the Rod Clamp Bridge

vertical

1. Open the rod clamp wing nut by

turning it counterclockwise.

2. If necessary, move the top screw to the middle hole.

Pushing away the clamping slide makes it easier to move the

screws.

3. Tighten both screws.

Mounting the Rod Clamp Bridge

horizontal

1. Open the rod clamp wing nut by

turning it counterclockwise

2. If necessary, move the top screw to the lower hole.

Pushing away the clamping slide makes it easier to move the

screws.

3. Tighten both screws.

8.5.2 Power ON / OFF

To turn the RCP-3

and

OFF

, press and hold down the Jog-

Wheel until the ARRI logo appears on the display.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands