ARRI ARTEMIS 2 User Manual Download Page 70

Page: 70 / 93

Installation and Operation

8.6

TST and BST Installation and Operation

ADVICE

Powering TRINITY 2 Head, Top and Bottom Stage at the same time

This would cause more than the allowed amount of volts to flow through the ARTEMIS 2

and TRINITY 2. Risk of damage to the accessories.

DO NOT power the TRINITY 2 Head, Top and Bottom Stage at the same time.
Use for powering TRINITY 2 Head OR Top Stage OR the Bottom Stage.

8.6.1 Installing TST/BST to Center Post

1. Locate the red dot on the main cable plug and socket. When

both marks are aligned, insert the LEMO 3B plug into the

socket.

2. Carefully place the TST/BST onto the center post fine thread.

3. Turn the blue docking ring with your fingers until the thread

fully engages.

4. Use the Post Tool to finally tighten the Docking Ring.

Summary of Contents for ARTEMIS 2






























































































Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands

ARRI ARTEMIS 2, User Manual

Search results

Summary of Contents for ARTEMIS 2

Reviews:

Related manuals for ARTEMIS 2

Brands by name

Popular brands