manualshive.com logo in svg

ARRI ARTEMIS 2, User Manual

Share
Download
ARRI ARTEMIS 2 User Manual Download Page 79

Installation and Operation

79

Switching ARTEMIS / TRINITY Mode

1.

Double-click

 the jog-wheel

2.

Turn

 the jog-wheel 

left

 to reach the current mode

3.

Click

 the actual mode once

4. Select the mode you want, by clicking once

5. Or select Exit to cancel the action

8.7.10 Battery Status

Home Screen BHM-2

This 

main page

 is displayed after switching on the BHM-2. 

It shows the selected modes:

 

TRINITY 

or

 ARTEMIS

Simultaneously

 or 

One By One

and the available 

total capacity

of the 

12V 

and 

24V power lines

.

Battery Status / System Status

This page shows the available capacity in volts or percent 

of each battery.

Values in percent can only be displayed if the batteries offer

one of the supported battery communication protocols.

If there is 

no

 such battery communication 

protocol

 available, 

the values are displayed in 

volt

 

only

.

If 

no

 battery is 

connected

 to the input or the battery is

completely

 

discharged

, a line is displayed.

Summary of Contents for ARTEMIS 2






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands