manualshive.com logo in svg

Arctic Cat PROWLER XT 2014, Service Manual

The Arctic Cat PROWLER XT 2014 is a high-performance off-road vehicle built to tackle rugged terrains with ease. To ensure the best maintenance and repair, a comprehensive Service Manual is available for download, completely free. Get your hands on this essential manual at manualshive.com and enhance your off-roading experience.

Share
Download
background image

102

CYLINDER/CYLINDER HEAD 
ASSEMBLY

NOTE: If the cylinder/cylinder head cannot be trued,

they must be replaced as an assembly.

Cleaning/Inspecting Cylinder Head

1. Using a non-metallic carbon removal tool, remove

any carbon buildup from the combustion chamber

being careful not to nick, scrape, or damage the com-

bustion chamber or the sealing surface.

2. Inspect the spark plug hole for any damaged threads.

Repair damaged threads using a “heli-coil” insert.

3. Place the cylinder head on the surface plate covered

with #400 grit wet-or-dry sandpaper. Using light

pressure, move the cylinder head in a figure eight

motion. Inspect the sealing surface for any indication

of high spots. A high spot can be noted by a bright

metallic finish. Correct any high spots before assem-

bly by continuing to move the cylinder head in a fig-

ure eight motion until a uniform bright metallic

finish is attained.

Measuring Cylinder Head 
Distortion

1. Remove any carbon buildup in the combustion

chamber.

2. Lay a straightedge across the cylinder head; then

using a feeler gauge, check the distortion between

the head and the straightedge.

3. Maximum distortion must not exceed specifications.

CC141D

Cleaning/Inspecting Cylinder

1. Wash the cylinder in parts-cleaning solvent.

2. Inspect the cylinder for pitting, scoring, scuffing,

warpage, and corrosion. If marks are found, repair

the surface using a cylinder hone (see Inspecting

Cylinder in this sub-section).

3. Place the cylinder on the surface plate covered with

#400 grit wet-or-dry sandpaper. Using light pressure,

move the cylinder in a figure eight motion. Inspect

the sealing surface for any indication of high spots.

A high spot can be noted by a bright metallic finish.

Correct any high spots before assembly by continu-

ing to move the cylinder in a figure eight motion

until a uniform bright metallic finish is attained.

CC129D

4. Using a slide gauge and a dial indicator or a snap

gauge, measure the cylinder bore diameter in three

locations from top to bottom and again from top to

bottom at 90° from the first measurements for a total

of six measurements. The trueness (out-of-round-

ness) is the difference between the highest and low-

est reading. Maximum trueness (out-of-roundness)

must not exceed specifications.

CC127D

5. Wash the cylinder in parts-cleaning solvent.

6. Inspect the cylinder for pitting, scoring, scuffing, and

corrosion. If marks are found, repair the surface

using a #320 grit ball hone.

CAUTION

Incorrect installation of the piston rings will result in
engine damage.

CAUTION

The cylinder head studs must be removed for this pro-
cedure.

CAUTION

Water or parts-cleaning solvent must be used in con-
junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

CAUTION

Water or parts-cleaning solvent must be used in con-
junction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

Summary of Contents for PROWLER XT 2014



























































































































































































































Reviews:

No comments

Related manuals for PROWLER XT 2014

Baja motorsports Trax Owner'S Manual preview
Trax
Brand: Baja motorsports Pages: 50
ODES Dominator Owner'S Manual preview
Dominator
Brand: ODES Pages: 136
Taylor-Dunn B0-254-48 Operation, T Roubleshooting And Replacement Parts Manual preview
B0-254-48
Brand: Taylor-Dunn Pages: 244
XY Powersports XY500UTV Service Manual preview
XY500UTV
Brand: XY Powersports Pages: 259
B.O.B COZ Owner'S Manual preview
COZ
Brand: B.O.B Pages: 36
Suzuki LT-F500F 2002 Service Manual preview
LT-F500F 2002
Brand: Suzuki Pages: 382
Dazon Raider Classic 250 Owner'S Manual preview
Raider Classic 250
Brand: Dazon Pages: 98
Ski-Doo Tundra Series Operator'S Manual preview
Tundra Series
Brand: Ski-Doo Pages: 159
Ski-Doo 2006 Mini Z Operator'S Manual preview
2006 Mini Z
Brand: Ski-Doo Pages: 103
Linhai LH40DA Owner'S/Operator'S Manual preview
LH40DA
Brand: Linhai Pages: 92
Aosom 370-234V80 Assembly Instruction Manual preview
370-234V80
Brand: Aosom Pages: 36
Yamaha PZ50W Owner'S Manual preview
PZ50W
Brand: Yamaha Pages: 88
Yamaha PZ500D Owner'S Manual preview
PZ500D
Brand: Yamaha Pages: 83
Yamaha PRO HAULER YXP1000 Owner'S Manual preview
PRO HAULER YXP1000
Brand: Yamaha Pages: 92
Yamaha Phazer PZ50GTY Owner'S Manual preview
Phazer PZ50GTY
Brand: Yamaha Pages: 98
Yamaha MM700H Owner'S Manual preview
MM700H
Brand: Yamaha Pages: 94
Yamaha Phazer Owner'S Manual preview
Phazer
Brand: Yamaha Pages: 98
Yamaha MM700G Owner'S Manual preview
MM700G
Brand: Yamaha Pages: 96

Brands by name

Popular brands

Load more brands