AMK Level 5 Installation, Operation And Troubleshooting Download Page 21

Page: 21 / 104

AMK Solac 11252 DeltaSol_BX.monen.ind

Level 5

System 7
Solar system with east-/west collectors

The controller compares the temperatures at the collector
sensors S1 and S5 to the store temperature at sensor S2.
If one of the measured temperature differences is higher

than the adjusted switch-on temperature differences, the
corresponding pump (R1, R2) will be activated and the store
will be loaded.

Sensor/Ter-
minal

Designation

Description

TCOL1

Temperature collector 1

TSTB

Temperature store base

Optional sensor for measurement
purposes or options

S4
S5

TCOL2

Temperature collector 2

VFS

Optional sensor for measurement
purposes or options

RPS
V40

Relay

Description

Solar pump collector 1

Solar pump collector 2

R2/R4

optional:
Thermal disinfection
Parallel relay
Heat dump

Adjustment channels

Channel

Sub channel 1

Sub channel 2 Factory

setting

Change to

Description

Page

ARR

System

LOAD >

DT O

4 K

Switch-on temperature difference

DT F

2 K

Switch-off temperature difference

DT1S

10 K

Set temperature difference

RIS

2 K

Rise

S MAX

75 °C

Store maximum limitation

SMAXS

Sensor store max

COL 1 >

Collector 1

CEM1

115 °C

Collector emergency temperature 1

OCCO1**

OFF

Option collector cooling 1

CMAX1

95 °C

Maximum collector temperature 1

OCMI1

OFF

Option collector minimum limitation 1

CMIN1

10 °C

Minimum collector temperature 1

Temp. Sensor

Pt1000

GND

VBus

PWM

V40

VFS

RPS

out

Summary of Contents for Level 5









































































































Search results

Summary of Contents for Level 5

Reviews:

AMK Level 5, Installation, Operation And Troubleshooting, Page: 21 / 104

Search results

Summary of Contents for Level 5

Reviews: