AMK Level 5 Installation, Operation And Troubleshooting Download Page 17

Page: 17 / 104

AMK Solac 11252 DeltaSol_BX.monen.ind

Level 5

The controller compares the temperature at sensor S1 to
the temperatures at sensors S2 and S4. If the measured tem-
perature differences are higher than the adjusted switch-on
temperature differences, the pump (R1) will be activated and

the corresponding store will be loaded up to the adjusted
maximum temperature via the valve (R3). Store 1 is loaded
with priority.

Sensor/Ter-
minal

Designation

Description

TCOL

Temperature collector

TST1B

Temperature store 1 base

Optional sensor for measurement
purposes or options

TST2B

Temperature store 2 base

Optional sensor for measurement
purposes or options

VFS
RPS
V40

Relay

Description

Solar pump

R2/R4

optional:
Thermal disinfection
Parallel relay
Heat dump

3-port valve store 1 / 2

Adjustment channels

Channel

Sub channel 1

Sub channel 2 Factory

setting

Change to

Description

Page

ARR

System

LOAD1 >

Loading 1

DT1O

4 K

Switch-on temperature difference 1

DT1F

2 K

Switch-off temperature difference 1

DT1S

10 K

Set temperature difference 1

RIS1

2 K

Rise 1

S1MAX

75 °C

Store maximum limitation 1

SMXS1

Sensor store max 1

LOAD2 >

Loading 2

DT2O

4 K

Switch-on temperature difference 2

System 5

2-store system with valve logic, 1 pump, 3 sensors and 3-port valve

Temp. Sensor

Pt1000

GND

VBus

PWM

V40

VFS

RPS

out

Note: 3-port valve normally open - store 1 (S2)

Summary of Contents for Level 5









































































































Search results

Summary of Contents for Level 5

Reviews:

AMK Level 5, Installation, Operation And Troubleshooting, Page: 17 / 104

Search results

Summary of Contents for Level 5

Reviews: