30
Trouble Shooting Guide
Problem
Cause
Remedy
Engine will not start
No fuel
Fill Fuel Tank
Fuel Tap has been closed
Open fuel tap.
Engine not primed.
(GX100 Only)
Push the Carburettor Primer Bulb 4 times and
pull the Recoil Handle until the Engine
¿
res
Engine not primed.
(Diesel Only)
See the Service & Maintenance section of this
Manual.
Spark Plug contaminated or damaged.
(Petrol Only)
Replace spark plug.
Faulty Carburettor.
(Petrol Only)
Service the Carburettor
Engine stops suddenly, or stops when
the engine rpm is increased.
See Above
See Above
Main jet of the Carburettor clogged with
dirt.
(GX120 Only)
Take out the main jet of the Carburettor and
clean with Compressed air.
Air
¿
lter element dirty.
Clean the element.
Spark plug cap is loose.
(Petrol Only)
Tightly
¿
t cap to plug.
Engine runs, but machine does not
produce impact.
Lack of engine power
See above.
Clutch is slipping
Dismantle clutch assembly, Clean shoe and
drum with proper solvent. Replace clutch
shoe if necessary.
Crank mechanism is damaged
Contact Dealer.
Before starting the Priming procedure, please ensure the Fuel Tank is full and the Fuel Cap is not
¿
tted to
the tank.
CAUTION
Maintenance
The Altrad Belle
RTX
Range is designed to give many years of trouble free operation. It is, however, important that the simple regular
maintenance listed in this section is carried out.
It is recommended that an approved Altrad Belle dealer carries out all major maintenance and repairs. Always use genuine Altrad Belle
replacement parts, the use of spurious parts may void your warranty.
Before any maintenance is carried out on the machine, switch off the engine. If working on a petrol engined machine, disconnect the
HT lead from the sparkplug.
Always set the
RTX
on level ground to ensure any
À
uid levels will be correctly read. Only use recommended oils (see chart).
Servicing the Engine
Service the engine according to the engine manufacturer’s speci
¿
cations. Refer to the engine operation and maintenance manual.
Yanmar L48 Engine Priming
In the event of running out of Diesel or after a change of the Fuel Filter, the Yanmar engine will need to be primed. Please follow the
below instructions.
Service & Maintenance
1. Open the fuel cock/tap.
2. Slide the Engine Speed Control Lever to the
RUN
position.
3. Using 2 x 17mm Spanners, unlock the Injector Pipe
(Item 1)
by loosening the
Injector Pipe Nut
(Item 2)
.
4. Slacken the Injector Pump Nozzle
(Item 3)
by 2 full revolutions
NOTE:- DO NOT
remove the Injector Pump Nozzle.
5. Hold the Injector Pipe away from the Injector Pump Nozzle and wait until
Diesel is running freely without any air bubbles.
6. Re-tighten the Injector Pump Nozzle to a setting of 12Nm.
7. Re-
¿
t the Injector Pipe and tighten to 12Nm.
8 Re-
¿
t the Fuel Cap and start the engine using the Start and Stop Proedure
section of this manual.
1
2
3
Summary of Contents for BELLE RTX
