manualshive.com logo in svg

Altera Stratix V Hard IP, User Manual, Page: 12 / 232

Share
Download
Altera Stratix V Hard IP User Manual Download Page 12

1–4

Chapter 1: Datasheet

Release Information

Stratix V Hard IP for PCI Express

June  2012

Altera Corporation

User Guide

1

This document describes both the Stratix V Hard IP for PCI Express which includes an 
Avalon-ST interface to the Application Layer and the Avalon-MM Stratix V Hard IP 
for PCI Express which includes an Avalon-MM interface to the Application Layer. In 
the interest of brevity, the remainder of this document does not use both product 
names.

f

The purpose of the 

Stratix V Hard IP for PCI Express User Guide 

is to explain how to use 

the Stratix V Hard IP for PCI Express

 

and not to explain the PCI Express protocol. 

Although there is inevitable overlap between these two purposes, this document 
should be used in conjunction with an understanding of the 

PCI Express Base 

Specification 3.0

Release Information

Table 1–3

 provides information about this release of the PCI Express Compiler.

1

If you have an existing Stratix V 11.1 or earlier design, you must regenerate it in 12.0 
before compiling in using the 12.0 version of the Quartus II software.

Altera verifies that the current version of the Quartus

®

  II software compiles the 

previous version of each IP core. Any exceptions to this verification are reported in the 

MegaCore IP Library Release Notes and Errata

. Altera does not verify compilation with 

IP core versions older than one release.

ECRC forwarding on RX and TX

Supported

Not supported

Number of MSI requests

16

1

MSI-X

Supported

Not supported

Legacy interrupts

Supported

Supported

Expansion ROM

Supported

Not supported

Notes to 

Table 1–2

:

(1) Not recommended for new designs.

(2) ×2 is supported by down training from ×4 or ×8 lanes. for Gen1, Gen2, and Gen3.

(3) Gen2 ×8 support is preliminary for the Avalon-MM interface

(4) The Quartus II software provides compilation and simulation support in the 12.0 release. It does not provide Programmer Object File (

.pof

) 

support in the 12.0 release. For Gen3 compilation support is not available for Stratix V ES silicon, production silicon is required.

(5) Refer to 

Appendix A, Transaction Layer Packet (TLP) Header Formats

 for the layout of TLP headers.

Table 1–2. Hard IP for PCI Express Features  (Part 2 of 2)

Feature

Avalon-ST Interface

Avalon-MM Interface

Table 1–3. PCI Express Compiler Release Information

Item

Description

Version

12.0

Release Date

June 2012

Ordering Codes

No ordering code is required 

Product IDs 

There are no encrypted files for the Stratix V Hard IP for PCI 
Express. The Product ID and Vendor ID are not required 
because this IP core does not require a license.

Vendor ID

Summary of Contents for Stratix V Hard IP









































































































































































































































Reviews:

No comments