manualshive.com logo in svg

Altera Stratix V Hard IP, User Manual, Page: 11 / 232

Share
Download
Altera Stratix V Hard IP User Manual Download Page 11

Chapter 1: Datasheet

1–3

Features

June 2012

Altera Corporation

Stratix V Hard IP for PCI Express

User Guide

write, and completion Transaction Layer Packets (TLPs) into standard Avalon-MM 
read and write commands typically used by master and slave interfaces. This PCI 
Express to Avalon-MM bridge also translates Avalon-MM read, write and read data 
commands to PCI Express read, write and completion TLPs. 

Table 1–2

 lists the 

features available for both variants.

Table 1–2. Hard IP for PCI Express Features  (Part 1 of 2)

Feature

Avalon-ST Interface

Avalon-MM Interface

MegaCore License

Free

Free

Native Endpoint 

Supported

Supported

Legacy Endpoint 

(1)

Supported

Not Supported

Root port

Supported

Not supported

Gen1

(2)

×1, ×4, ×8

×1, ×4, ×8

Gen2 

(2)

×1, ×4, ×8 

×1, ×4, ×8

(3)

Gen3 

(2)

 

(4)

×1, ×4, ×8 

×1, ×4

MegaWizard Plug-In Manager design flow

Supported

Not supported

Qsys design flow

Supported

Supported

64-bit Application Layer interface

Supported

Supported

128-bit Application Layer interface

Supported

Supported

256-bit Application Layer interface

Supported

Not supported

Transaction Layer Packet type (TLP)

(5)

■

Memory Read Request

■

Memory Read Request-
Locked

■

Memory Write Request

■

I/O Read Request

■

I/O Write Request

■

Configuration Read Request 
(Root Port)

■

Configuration Write Request 
(Root Port)

■

Message Request

■

Message Request with Data 
Payload

■

Completion without Data

■

Completion with Data

■

Completion for Locked Read 
without Data

■

Memory Read Request

■

Memory Write Request

■

Completion without Data

■

Completion with Data

Payload size

128–2048 bytes

128–256 bytes

Number of tags supported for non-posted 
requests

32 or 64

8

Low power mode using 62.5 MHz clock

Supported

Supported

Reordering of -out-of-order completions 
(transparent to the Application Layer)

Not supported

Supported

Requests that cross 4 KByte address boundary 
(transparent to the Application Layer)

Not supported

Supported

Summary of Contents for Stratix V Hard IP









































































































































































































































Reviews:

No comments