manualshive.com logo in svg

Altera Stratix V Hard IP, User Manual, Page: 117 / 232

Share
Download
Altera Stratix V Hard IP User Manual Download Page 117

Chapter 6: IP Core Interfaces

6–33

Completion Side Band Signals

June 2012

Altera Corporation

Stratix V Hard IP for PCI Express

User Guide

Completion Side Band Signals 

Table 6–11

 describes the signals that comprise the completion side band signals for the 

Avalon-ST interface. The Stratix V Hard IP for PCI Express provides a completion 
error interface that the Application Layer can use to report errors, such as 
programming model errors. When the Application Layer detects an error, it can assert 
the appropriate 

cpl_err

 bit to indicate what kind of error to log. If separate requests 

result in two errors, both are logged. The Hard IP sets the appropriate status bits for 
the errors in the Configuration Space, and automatically sends error messages in 
accordance with the 

PCI Express Base Specification

. Note that the Application Layer is 

responsible for sending the completion with the appropriate completion status value 
for non-posted requests. Refer to 

Chapter 13, Error Handling

 for information on 

errors that are automatically detected and handled by the Hard IP.

f

For a description of the completion rules, the completion header format, and 
completion status field values, refer to Section 2.2.9 of the 

PCI Express Base 

Specification, Rev. 2.1

.

Table 6–11. Completion Signals for the Avalon-ST Interface (Part 1 of 2)

Signal

I/O

Description

cpl_err[6:0]

I

Completion error. This signal reports completion errors to the Configuration 
Space. When an error occurs, the appropriate signal is asserted for one cycle.

■

cpl_err[0]

: Completion timeout error with recovery. This signal should be 

asserted when a master-like interface has performed a non-posted request 
that never receives a corresponding completion transaction after the 50 ms 
timeout period when the error is correctable. The Hard IP automatically 
generates an advisory error message that is sent to the Root Complex. 

■

cpl_err[1]

: Completion timeout error without recovery. This signal should 

be asserted when a master-like interface has performed a non-posted request 
that never receives a corresponding completion transaction after the 50 ms 
time-out period when the error is not correctable. The Hard IP automatically 
generates a non-advisory error message that is sent to the Root Complex. 

■

cpl_err[2]

: Completer abort error. The Application Layer asserts this signal 

to respond to a non-posted request with a Completer Abort (CA) completion. 
The Application Layer generates and sends a completion packet with 
Completer Abort (CA) status to the requestor and then asserts this error signal 
to the Hard IP. The Hard IP automatically sets the error status bits in the 
Configuration Space register and sends error messages in accordance with 
the 

PCI Express Base Specification, Rev. 2.1

.

■

cpl_err[3]

: Unexpected completion error. This signal must be asserted 

when an Application Layer master block detects an unexpected completion 
transaction. Many cases of unexpected completions are detected and reported 
internally by the Transaction Layer. For a list of these cases, refer to 

“Transaction Layer Errors” on page 13–3

. 

Summary of Contents for Stratix V Hard IP









































































































































































































































Reviews:

No comments