Alpha-InnoTec Luxtronik Operating Manual Download

Page: 20 / 52

Subject to technical amendments without prior notice | 83055400iUK – 2.1 | ait-deutschland GmbH

Query InfoLog

NOTE

Menu entry is only displayed if customer service access is

activated.

Errors that occur during operation of the heat pump are stored in

a list in the InfoLog. Each error is timestamped.
The error list contains a maximum of 100 entries. The last error

that occurred is at the top of the list. If there are more than 100 en-

tries, the oldest (= last) entry in the list is overwritten.

The menu is not shown in full here.

Query Inverter

NOTE

Menu entry is only displayed if customer service access

is activated. The list displayed on the screen is for service

purposes only.

The menu is not shown in full here.

Query Smart

NOTE

Menu entry is only displayed if customer service access is

activated and if:

●

Menu entry “room stat.” is set to “Smart”

●

“Smart“ settings have been made.



page 24, “Determining system setting“, “room stat.”



page 33, “Smart“

The menu is not shown in full here.

set temperature HC

Setpoint temperature heating circuit

set temperature MC1

Setpoint temperature mixing circuit 1

Targ. service water

Set point temperature domestic hot

water preparation

target value max

Highest requirement setpoint from the

Smart system

UFH total HC

Number of floor heating circuits

assigned to the heating circuit

UFH open HC

Number of open floor heating circuits

assigned to the heating circuit

numb.actuat. HC

Number of radiator drives assigned to

the heating circuit

Cur. room temp. HC

Current room temperature of the worst

room in the heating circuit

Targ. room temp. HC

Target temperature of the worst room

in the heating circuit

UFH total MC1

Number of floor heating circuits

assigned to the mixing circuit 1

UFH open MC1

Number of open floor heating circuits

assigned to the mixing circuit 1

numb.actuat. MC1

Number of radiator drives assigned to

the mixing circuit 1

Cur. room temp. MC1

Current room temperature of the worst

room in the mixing circuit 1

Targ. room temp. MC1 Target temperature of the worst room

in the mixing circuit 1

Summary of Contents for Luxtronik





















































Search results

Summary of Contents for Luxtronik

Reviews:

Related manuals for Luxtronik

Brands by name

Popular brands

Alpha-InnoTec Luxtronik, Operating Manual

Search results

Summary of Contents for Luxtronik

Reviews:

Related manuals for Luxtronik

Brands by name

Popular brands