Alpha-InnoTec Luxtronik Operating Manual Download

Page: 28 / 52

Subject to technical amendments without prior notice | 83055400iUK – 2.1 | ait-deutschland GmbH

Ventilating the system

The menu is not shown in full here.

Heat.sys.pump

Heating and floor heating circulating

pump

suppl.pump

additional circulating pump

DHW pump

Domestic hot water circulation pump

fan-heats.pump

Fan, well or brine circulation pump

MC open 1

Mixer 1 OPEN

MC close 1

Mixer 1 CLOSE

Circulation pump

fan nozzle heating

Fan nozzle heating

open exp. valve

In LWD the expansion valve opens

completely for the set running time.

Duration

Running time of the ventilation

1. Activate and select system part(s) to be ventilated.

2. Activate and select menu field “duration”, set running time

(hour cycle).

Duration
Factory setting: 1 hour
Value range for running time = 1 – 24 hours.
Save settings.

NOTE

If circulating pumps are selected, the ventilation program

will start immediately after the settings have been saved.

The ventilation pauses after one hour for 5 minutes and

then automatically continues afterwards.

aux. heat. hot water

Hot water reheating

Hot water reheating function

deactivated (in the factory)

Yes

Activated, the required hot water value

becomes the hot water target value



Part 1 of the controller manual, program area„Domestic Hot

Water“, section “Hot water reheating“

aux.serv.water max. maximum time period for hot water

reheating

maximum time period, during which the hot water should

be reheated. If this time period is exceeded the hot water

reheating is cancelled.

high pressure limit

Switch-off value high pressure (sensor)

low pressure limit

Switch-off value low pressure (sensor)

power 2hg

Power output of the electric heating

element (= additional heat generator)

smart grid

Smart Grid function switched off

Yes

Smart Grid function switched on



page 33, “Smart Grid“

setting mc 1

Mixing circuit 1 speed

fast

fast control speed

medium

average control speed

slow

slow control speed

Comp-Heater

Compressor heating

Yes

Compressor heating activated

Compressor heating deactivated

The compressor heating will be detected and regulated

automatically – insofar as present in the device. The setting

here is used for manual control during servicing.

Cooling

with CP

Additional circulation pump runs

during cooling operation

wo. CP

Additional circulation pump does not

run during cooling operation

Scroll all the way down,
save the settings.

Summary of Contents for Luxtronik





















































Search results

Summary of Contents for Luxtronik

Reviews:

Related manuals for Luxtronik

Brands by name

Popular brands

Alpha-InnoTec Luxtronik, Operating Manual

Search results

Summary of Contents for Luxtronik

Reviews:

Related manuals for Luxtronik

Brands by name

Popular brands