161 +MRR: 54000 x x x x x
162 +MRR: 56000 x x x x x
165 CONNECT 32000 x x x x x
166 CONNECT 34000 x x x x x
167 CONNECT 36000 x x x x x
168 CONNECT 38000 x x x x x
169 CONNECT 40000 x x x x x
170 CONNECT 42000 x x x x x
171 CONNECT 44000 x x x x x
172 CONNECT 46000 x x x x x
173 CONNECT 48000 x x x x x
174 CONNECT 50000 x x x x x
175 CONNECT 52000 x x x x x
176 CONNECT 54000 x x x x x
177 CONNECT 56000 x x x x x
178 CONNECT 230400 x x x x x
180 CONNECT 28000 x x x x x
181 CONNECT 29333 x x x x x
182 CONNECT 30667 x x x x x
183 CONNECT 33333 x x x x x
184 CONNECT 34667 x x x x x
185 CONNECT 37333 x x x x x
186 CONNECT 38667 x x x x x
187 CONNECT 41333 x x x x x
188 CONNECT 42667 x x x x x
189 CONNECT 45333 x x x x x
190 CONNECT 46667 x x x x x
191 CONNECT 49333 x x x x x
192 CONNECT 50667 x x x x x
193 CONNECT 53333 x x x x x
194 CONNECT 54667 x x x x x
195 +MRR: 28000 x x x x x
196 +MRR: 29333 x x x x x
197 +MRR: 30667 x x x x x
198 +MRR: 33333 x x x x x
199 +MRR: 34667 x x x x x
200 +MRR: 37333 x x x x x
201 +MRR: 38667 x x x x x
202 +MRR: 41333 x x x x x
203 +MRR: 42667 x x x x x
204 +MRR: 45333 x x x x x
205 +MRR: 46667 x x x x x
206 +MRR: 49333 x x x x x
207 +MRR: 50667 x x x x x
208 +MRR: 53333 x x x x x
209 +MRR: 54667 x x x x x
Notes:
1. An 'x' in a column indicates that the message (either the long form if verbose, or the value only for short form) will
be generated when that particular value of 'n' (shown at the top of the column) has been selected by the use of
ATXn. If the column is blank, then no message will be generated for that x option. A numeral indicates which less
explicit message (verbose or short form) will be output for that X option. (Also, see Section 3.3).
&C - RLSD Behavior
This parameter determines how the state of the Received Line Signal Detector (RLSD) output
relates to the detection of received line signal from the distant end. Changing the parameter
will take effect immediately in both the command and online command states.
In &C1 mode of operation, RLSD is not turned off until all data previously received from the
remote modem is delivered to the local DTE. However, such buffered data will be discarded
and RLSD will be turned off if the DTE turns off DTR (if &D1 or &D2 is set).
Syntax
&C[<value>]
Defined Values
<value> Decimal number corresponding to the selected option.
0 RLSD is always ON.
1 RLSD follows the state of the carrier. (Default.)
