Alliance Laundry Systems IYG065J Original Instructions Manual Download

Page: 87 / 106

Troubleshooting

Problem

Cause

Solving the problem

When the power is switched on : the dis-
play is not illuminated

No external power

Switch on the external power supply

Verify the external power to the machine

The emergency button is activated

Deactivate the emergency button

The power connector is not connected on
the board

Connect the power connector

The power connector is inverse connected

Check the wiring and connect the connec-
tor as it must be

The fuse on the wash computer has burned If the transformer is broken replace the

wash computer

Disconnect the input connector A & B

Check the wiring and the voltage at the
power Connector

The connector between the CPU and the
I/O board of the wash computer is either
absent or incorrectly pushed in.

If the transformer is still OK change the
Fuse

If the display is lighting up: verify if the
input signals or the +16Vdc Supply Sig-
nal are touching the cabinet

The display is illuminated, but it’s difficult
to read the text on the display.

The brightness is not Ok

Change the value for Brightness, Viewing
Angle in the Configuration Menu until you
get a bright display

The display just shows “Bootloader”but
the application does not run.

There is no SW loaded in the application

Load the application software from the
USB flash drive

The machine is not responding on pressing
the keyboard buttons

No button is functional

There is no beep signal when the buttons
are pressed

Check if the connector "K" of the key-
board is well connected

The coins have been inserted but the price
does not count down on the display.

The contact attached to the slot is not
functioning

The optical sensor attached to the slot is
not functioning

Check the electrical wiring of the slot

Make sure that you entered the coin val-
ue in the Payment menu

Check correct functioning of the slot con-
tact. Check that positive impulses are
generated

Check correct functioning of the optical
sensor. Check that positive impulses are
generated.

If the electrical connection is faulty, re-
pair it.

Enter correct coin value in the Payment
menu

Table 52

continues...

Troubleshooting

DO NOT COPY or TRANSMIT

Part No. D1631ENR7

Summary of Contents for IYG065J











































































































Search results

Summary of Contents for IYG065J

Reviews:

Related manuals for IYG065J

Brands by name

Popular brands

Alliance Laundry Systems IYG065J, Original Instructions Manual

Search results

Summary of Contents for IYG065J

Reviews:

Related manuals for IYG065J

Brands by name

Popular brands