Alliance Laundry Systems IYG065J Original Instructions Manual Download

Page: 105 / 106

9. Now you can Switch On the power supply.
10. The display should illuminate.

WARNING

Make sure that the small hose of the level sensor is
correctly secured by a flexible clamp.

If the hose is not air tight then the level sensor will
not make a correct measurement.

Make sure that you don´t damage the flex cable of
the keypad when you put the wash computer back
into the machine.

C084

Instructions for Installing New Software

1.   Switch the machine power supply off.
2.   Open the cover plate of the washing machine.
3.   Insert a flash drive containing the software into the USB con-

nector E (of the CPU board).

4. Switch the machine power supply on.
5. The display shows information that the software is being cop-

ied from the flash drive into the programmer board.

6. When the copying is finished a prompt to remove the flash

drive from the CPU is displayed.

7. Switch the machine power supply off and remove the flash

drive.

8. Close the washing machine cover plate.
9. Switch the machine power supply on.
10. If the software is compatible with the previous software the

new software can be used without re-initialization.

11. Clear all error messages in the Service-menu if you want to

verify correct functionality of the new installed software.

If the software is not 100% compatible with the previous soft-
ware version:

• A message which says “New SW version” will appear fol-

lowed by a prompt to enter a password for initialization of the
Configuration Menu

• In Configuration Menu, select Reset Factory Setting. This is

explained in Chapter

Basic Description of Controls

• Go through the Menu items of the Configuration and Initiali-

zation Menu one by one to ensure that all settings correspond
with the ones you prefer.

• All Custom Settings will be lost.

Service Information

DO NOT COPY or TRANSMIT

105

Part No. D1631ENR7

Summary of Contents for IYG065J











































































































Search results

Summary of Contents for IYG065J

Reviews:

Related manuals for IYG065J

Brands by name

Popular brands

Alliance Laundry Systems IYG065J, Original Instructions Manual

Search results

Summary of Contents for IYG065J

Reviews:

Related manuals for IYG065J

Brands by name

Popular brands