background image

• Soak
• Spray
• No wash

• No temperature can be programmed as a Rinse is only dedi-

cated for cold water.

The Rinse Sequence

Display Mes-

sage

Default

Information

Limits

Inlet

I1-I2-I7

3 Inlets can be programmed.

The suggested inlet valves are related to the temperature and the soap
box to be used.

NOTE: If you insert other inlet valves than the suggested
ones, problems can occur at the water fill process.

I1,2,3,4,7

Level

Normal High

The suggested water level depends on the machine Type.

Refer to 

Table 6 

RPM

-

The suggested RPM depends on the machine Type.

Refer to 

Table 7 

Detergents
Menu…

Supply 1, …, 8

0 seconds

Time selection for Soap Boxes (hopper) and external liquid soap sup-
plies.

You can program up to 4 supplies at the same time. If you have pro-
grammed more then 4 supplies an error message will be generated.
Put the time of the supplies back to zero until not more than 4 non-
zero time values are remaining.

(liquid soap supplies must be switched on at the configuration menu) .

0 - 99 seconds

On Time

12 seconds

The wash action (motor "On" Time).

Gentle wash action : 3 seconds.

(The suggested default values can be adjusted at the Initialization
menu)

1 - 99 seconds

Off Time

3 seconds

The wash action (motor "Off" Time). Gentle wash action : 12 sec-
onds. (The suggested default values can be adjusted at the Initializa-
tion menu)

1 - 99 seconds

Time

2.0 minutes

The Rinse Sequence Time.

(for 0 Minutes the Rinse sequence will be skipped) (programmable in
steps of 0.5 Minutes)

0 - 99.5 minutes

Pause

No

When a signal Pause is programmed, a pause will be introduced at the
end of the Wash Step. This allows the operator to add soap for the next
step. A buzzer signal warns the operator that the cycle has been inter-
rupted.

No / Yes

Table 21

 The Final Rinse Sequence

• Prewash
• Wash
• Cooldown
• Rinse

Final Rinse

• Soak
• Spray
• No wash

• No temperature can be programmed as a Last Rinse is only

dedicated for cold (hard) water.

Programming

©

 Copyright, Alliance Laundry Systems LLC -

 DO NOT COPY or TRANSMIT

  52

  Part No. D1631ENR7

Summary of Contents for IYG065J











































































































Reviews: