manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 92 / 176

Share
Download
Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 92

92

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 5

Configure the I/O Modules

Save and Download the 
Module Configuration

We recommend that after a module is configured you save your work.

If after downloading the program the MS and NS indicators on the Guard I/O 
module are not both solid green, this state can be due to loss of ownership. The 
ownership is based on the following items:

• Guard I/O EtherNet/IP address
• Guard  I/O  safety  network  number
• GuardLogix  slot  number
• GuardLogix safety network number
• Path from GuardLogix controller to Guard I/O module
• Configuration signature

If any of these items change, the connection between the GuardLogix 
controller and the Guard I/O module is lost, and the yellow yield in the project 
tree appears. Reset ownership to re-establish the connection by using this 
procedure.

1. Open the safety I/O module properties.

2. Choose the Safety tab.

3. From the dialog box, choose Reset ownership.

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Reviews:

No comments