manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, User Manual, Page: 167 / 176

Share
Download
Allen-Bradley 1732ES-IB12XOB4 User Manual Download Page 167

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

167

Specifications

Appendix D

Table 76 -  1732ES-IB16, 1732ES-IB8XOB8, 1732ES-IB8XOBV4, 1732ES-IB12XOB4, and 1732ES-IB12XOBV2 Modules – Environmental 
Specifications

Attribute

Value

Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)

-20…+55 °C (-4…+131 °F)
(All 1732ES modules except 1732ES-IB16 modules)

Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock)

-20…+60 °C (-4…+140 °F)
(Only 1732ES-IB16 modules)

Temperature, nonoperating
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock)

-40…+85 °C (-40…+185 °F)

Relative humidity
IEC 60068-2-30 (Test Db, Unpackaged Nonoperating Damp Heat)

 5…95% noncondensing

Vibration
IEC 60068-2-6 (Test Fc, Operating)

5 g at 10…500 Hz

Shock, operating
IEC 60068-2-27 (Test Ea, Unpackaged Shock)

30 g

Shock, nonoperating
IEC 60068-2-27 (Test Ea, Unpackaged Shock)

50 g

Emissions

IEC 61000-6-4

ESD immunity
IEC 61000-4-2

4 kV contact discharges
10 kV air discharges

Radiated RF immunity
IEC 61000-4-3

10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
10V/m with 200 Hz 50% Pulse 100% AM at 900 MHz
10V/m with 200 Hz 50% Pulse 100% AM at 1890 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz

Conducted RF immunity
IEC 61000-4-6

 10V rms with 1 kHz sine-wave 80% AM from 
150 kHz…80 MHz

EFT/B immunity
IEC 61000-4-4

±2 kV at 5 kHz on power ports
±1 kV at 5 kHz on signal ports
±1 kV at 5 kHz on communication ports

Surge transient immunity
IEC 61000-4-5

±2 kV line-earth (CM) on power ports
±2 kV line-earth (CM) on signal ports
±2 kV line-earth (CM) on communication ports

Reaction time

Input reaction time, max

16.2 ms + set values of ON/OFF delays

Output reaction time, max

6.2 ms + (20 ms) relay response time

Signal sequence

Typ. 600 ms

While safety outputs are in an on state, the signal sequence shown in the figure is output 
continuously for fault diagnosis. Confirm response time of device connected to safety outputs so 
the device does not malfunction due to off pulse.

Typ. 700 μs

Summary of Contents for 1732ES-IB12XOB4

















































































































































































Reviews:

No comments